RCC series
1 / 6ページ

RCC COMPACT LOW PROFILE HIGH THRUST LOADS PATENT PENDING switch slots for PHD’s Series 6790 reed and solid state switches optional switch magnet anodized aluminum housing optional rear ports standard pinion is hard coated with a thru and threaded mounting hole (uni-mount) optional hollow pinion (-Q2 option) allows pneumatic porting or electrical lines to pass through from the back of the unit to the output hub optional additional threaded mounting holes (-Q19 or -Q29) for versatile mounting options standard thru mounting holes in the body are threaded to provide versatility and ease of mounting anodized aluminum body with TC bearing for high wear resistance and lower friction sintered bronze breather caps anodized piston with block vee urethane seals side ports (standard) optional flow control kits provide accurate control of rotational speed angle adjustment screw urethane shock pad provides quiet operation and deceleration with angle adjustment screw multi-function cable and guide seal stainless steel cable with nylon jacket aircraft quality low fatigue, multi-stranded top and bottom thrust bearing Major Benefits Industry Uses Exceptionally low profile for confined spaces Three bore sizes and two standard rotations, 90° and 180° Standard internal shock pad eliminates metal to metal contact, reducing noise and end-of-rotation impact forces The rotary housing incorporates switch slots for convenient mounting of PHD’s Series 6790 4 mm Reed and Solid State Switches. Magnet option (-M) is required when using Series 6790 Switches Standard angle adjustment of ± 5° each direction Standard pinion has a threaded thru hole High axial thrust load capabilities Light part rotation Electronic assembly Labeling applications Grip and flip applications

ORDERING DATA: SERIES RCC ROTARY ACTUATORS TO ORDER SPECIFY: Product, Series, Type, Design No., Bore Size, Rotation, and Options. TYPE C - Heavy Duty Composite Bearing ROTATION SPEED CONTROL VALVE PB - Rotational Speed Controls both directions DESIGN NO. 1 - Imperial 5 - Metric Options may affect unit length. See unit dimension and options pages for adders. OPTIONS Dowel pin (transition fit) Dowel pin (precision fit) Magnet for Series 6790 & JC1 Switches Hollow pinion Hollow pinion with mounting holes Combined mount (uni-mount center hole with hub mounting holes) UB66 - Rear ports Z1 -...

ENGINEERING DATA: SERIES RCC ROTARY ACTUATORS SPECIFICATIONS MIN. OPERATING PRESSURE MAX. OPERATING PRESSURE OPERATING TEMPERATURE RANGE ROTATIONAL TOLERANCE BACKLASH DEGREES OF ROTATION LUBRICATION BASE WEIGHT SIZE ROTATION lb kg .32 .15 90¡ 08 .31 .14 180¡ .65 .30 90¡ 12 .61 .28 180¡ 1.20 .55 90¡ 16 1.16 .53 180¡ RCCx12 RCCx16 25 psi [1.7 bar] 20 psi [1.4 bar] 100 psi [7 bar] 32 to 150¡F [0 to 65¡C] Nominal +10¡ to -10¡ with angle adjustment No backlash at end of rotation 90¡ and 180¡ Permanent for non-lube air MAX. AXIAL BEARING LOAD lb N MAX. RADIAL BEARING LOAD* lb N NOTE: *At .5 in...

DIMENSIONS: SERIES RCC ROTARY ACTUATORS R2 A E 3X MANUFACTURING FEATURE CONTACT PHD FOR MORE INFORMATION U THREAD THIS SIDE V SHCS FROM OPPOSITE SIDE W SHCS FROM THIS SIDE Y THREAD FROM OPPOSITE SIDE 2 NOTES: 1) CIRCLED NUMBERS INDICATE POSITION 2) HUB SHOWN IN MID-ROTATION POSITION BORE SIZE NOMINAL ROTATION BORE SIZE NOMINAL ROTATION All dimensions are reference only unless specifically toleranced.

OPTIONS: SERIES RCC ROTARY ACTUATORS TRANSITIONAL FIT DOWEL PIN HOLES This option provides a compromise fit between clearance and interference. Transitional fits are used where accuracy of location is important, but a small amount of clearance is permissible. SIZE 08 12 16 This option provides a H7 tolerance precision fit with dowel pins. Precision fits are used where accuracy of location is of prime importance and for parts requiring rigidity and alignment. DIAMETER ¯ .1183 [¯ 3.005] ¯ .1183 [¯ 3.005] ¯ .15765 [¯ 4.004] MAGNET FOR PHD SERIES 6790 & JC1 SWITCHES SERIES 6790 & JC1SDx CORDSET...

OPTIONS: SERIES RCC ROTARY ACTUATORS ¯ A THRU HOLLOW PINION This option provides a through hole for feeding pneumatic or electrical lines through the pinion. 3X MANUFACTURING FEATURE CONTACT PHD FOR MORE INFORMATION HOLLOW PINION WITH HUB MOUNTING HOLES This option provides the Q2 pinion, along with the addition of threaded mounting holes. Hub shown at mid-rotation position. 08 mm 90¡ UNITS ONLY ¯ D BOLT CIRCLE ¯ A THRU ¯ D BOLT CIRCLE 2X MANUFACTURING FEATURE CONTACT PHD FOR MORE INFORMATION This option provides the standard threaded through mounting hole and the addition of threaded...