D2 series
1 / 10ページ

General Specifications Electrical Capacity (Resistive Load) Logic Level: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Contact Timing: Angle of Throw: Materials & Finishes Toggle/Lever: Bushing: Support Bracket: Housing: Base: Movable Contacts: Stationary Contacts: Terminals: Environmental Data Operating Temp Range: Humidity: Vibration: Shock: Soldering: Cleaning: Standards & Certifications Flammability Standards: 0.4VA maximum @ 48V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 48V) Note: Find additional explanation of operating range in Supplement section. 50 milliohms maximum 1,000 megohms minimum @ 500V DC 1,000V AC minimum between contacts for 1 minute minimum; 1,500V AC minimum between contacts & case for 1 minute minimum 100,000 operations minimum for bat lever models 50,000 operations minimum for locking lever models 50,000 operations minimum Nonshorting (break-before-make) 24° Brass with chrome plating Brass with nickel plating Straight PC: phosphor bronze with tin plating; right angle & vertical: brass with tin plating Polybutylene terephthalate (PBT) (UL94V-0) 1- and 2-pole GFR polyamide (UL94V-0); 4-pole liquid crystal polymer (LCP) (UL94V-0) Phosphor bronze with gold plating Brass with gold plating Brass with gold plating –10°C through +70°C (+14°F through +158°F) 90 ~ 95% humidity for 240 hours @ 40°C (104°F) 10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) Wave Soldering recommended. See Profile A in Supplement section. Manual Soldering: 1- & 2-pole: 3 seconds maximum @ 350°C maximum; 4-pole: 4 seconds maximum @ 410°C maximum Hand clean locally using alcohol based solution. See Cleaning specifications in Supplement section. UL94V-0 rated housing & base The D2 Series toggles have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-current, logic level circuit. When used as intended in a logic level circuit, the results do not produce hazardous energy. PCB Mount Miniature Toggles

Distinctive Characteristics PCB Mount Miniature Toggles Base of heat resistant resin meets UL94V-0 flammability rating. Maximized voltage capability of 48V allows use in medium source applications and increases operating life. Award-winning STC contact mechanism with benefits unavailable in conventional mechanisms: smoother positive detent actuation, increased contact stability, and unparalleled reliability. (Additional STC details under Terms and Acronyms in the Supplement section.) Round .031” (0.8mm) diameter PC terminals for easy PCB assembly. Terminal spacing conforms to standard .100”...

PCB Mount Miniature Toggles TYPICAL SWITCH ORDERING EXAMPLE * Combines with ON-NONE-ON circuit only & not available with Right Angle .413” (10.5mm) Bat Lever .200” (5.1mm) Diameter Locking Lever Straight with Bracket Right Angle w/Bracket Vertical with Bracket DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Touch SPDT ON-NONE-ON Circuit

POLES & CIRCUITS Terminal numbers are not actually on the switch. Throw & Schematics Connected Terminals .413” (5.1mm) Diameter Locking Lever Material: Chrome over brass Material: Chrome over brass Straight with Bracket Right Angle with Bracket Vertical with Bracket Toggle Position ( ) = Momentary PCB Mount Miniature Toggles Material: Polyethylene Colors Available: ABCEFG AT427 Cap Supplied with Locking Lever 24° (4.8) Dia .189 Colors Codes: Colors Available: ABCEFG A Black Material: Anodized Aluminum Colors Available: ACG E Yellow Material: Polyethylene OPTIONAL CAPS & CAP COLORS

PCB Mount Miniature Toggles TYPICAL SWITCH DIMENSIONS Straight PC • Single Pole Straight PC • Double Pole Actuator in Down Position Tactiles Tilt Straight PC • Four Pole Actuator in Down Position (0.3) .012 Actuator in Down Position www.nkk.com Accessories Supplement

Actuator in Down Position Actuator in Down Position Straight PC • Bracket Four Pole Actuator in Down Position www.nkk.com Straight PC • Bracket Double Pole Straight PC • Bracket Single Pole TYPICAL SWITCH DIMENSIONS PCB Mount Miniature Toggles

PCB Mount Miniature Toggles TYPICAL SWITCH DIMENSIONS Right Angle PC • Single Pole (6.2) Dia .244 Rotaries Slides Actuator in Down Position Right Angle PC • Double Pole (6.2) Dia .244 Actuator in Down Position www.nkk.com

TYPICAL SWITCH DIMENSIONS Vertical PC • Single Pole (0.3) Typ .012 3 Actuator in Down Position Vertical PC • Double Pole PCB Mount Miniature Toggles Actuator in Down Position www.nkk.com

PCB Mount Miniature Toggles TYPICAL SWITCH DIMENSIONS Vertical PC • Four Pole Actuator in Down Position STANDARD HARDWARE AT513M Hex Nut Brass with nickel plating 2 supplied AT507M Locking Ring Steel with zinc/chromate 1 supplied OPTIONAL AT509 Lockwasher Steel with zinc/chromate 1 supplied AT501M Knurled Face Nut Brass with chrome plating PANEL CUTOUTS & MAXIMUM PANEL THICKNESS Without Bottom Hex Nut With Standard Hardware .087” (2.2mm) for Standard Lever .051” (1.3mm) for Locking Lever Without Locking Ring Without Locking Ring & Bottom Hex Nut .185” (4.7mm) for Standard Lever .142”...