UE series
1 / 12ページ

カタログの抜粋

TUBE MAKE-TO-ORDER PRODUCTS Tube for Anti-Static Environment Anti-Static Tube dissipative Resin (Surface Resistivity : 10 4~10 7Ω). ●Classification of conductivity region Anti-Static Tube Clean Room Tube Antistatic material Stalic dissipative material Shielding material Carbon fiber and powder Cutting mark Cutting mark Anti-Stalic Tube Tube Binder for Electrostatic Discharging and Antistatic Applications. ● Marking Anti-Spatter Tube Tube cutter Insert Ring Tube Reel

カタログの1ページ目を開く

Tube Series ■ Model Designation (Example) UE Anti-Static Tube Anti-Static Tube Tube color: B (Black) only ② Tube length ② Tube length Code 651 Standard Tube Multi-core Tube Coiling Tube Twin Coiling Tube Fluororesin / Polyamide Tube Clean Room Tube Anti-Spatter Tube Anti-Stalic Tube

カタログの2ページ目を開く

■ Specifications Fluid medium Max. operating pressure (at 20℃ 65%RH) Max. vacuum Operating temp. range Warning ※ . The value of max. operating pressure is measured at 20℃ and 65%RH. When Tubes are used in different conditions, consider a safety ratio of the pressure with an enough margin, referring to Burst Pressure Curve. When Tubes are frequently swung and bent, there is a possibility of generating heat between molecules and damaging the products. TUBE ■ Burst Pressure Curve (Reference value) MAKE-TO-ORDER PRODUCTS Detailed Safety Instructions Before using PISCO products, be sure to read...

カタログの3ページ目を開く

Tube Series Anti-Static Tube 653 Standard Tube Multi-core Tube Coiling Tube Twin Coiling Tube Fluororesin / Polyamide Tube Clean Room Tube Anti-Spatter Tube Anti-Stalic Tube Anti-Static Tube Model code Tube length Min. Bending Radius Min. Installation Radius (mm) (mm) (m) ※ . □ in model code : Replace with Tube length

カタログの4ページ目を開く

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

カタログの5ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

カタログの6ページ目を開く

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

カタログの7ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a...

カタログの8ページ目を開く

Safety Instructions 7. Instructions for Tube Disconnection ① Make sure there is no air pressure inside of the tube, before disconnecting it. ② Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. By insufficient pushing of the releasering, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. 8. Instructions for Installing a fitting ① When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting...

カタログの9ページ目を開く

Tube Series Common Safety Instructions for Tubes Before selecting or using PISCO products, read the following instructions. Read the detailed instructions for individual series as well as the instructions below. Warning 1. Avoid any load on Tubes such as tensile strength, twisting and bending. These may cause the crush, burst and escape of Tubes. 2. Protect Tubes from scratches caused by snagging or kinking. It may cause the burst of Tubes. 3. The burst pressure of Tubes drops as temperature rises. Read the operating pressure in the catalog well, and apply safety factor. 4. The minimum...

カタログの10ページ目を開く

Caution 1. When bending tubes, observe the minimum bending radius and minimum installation radius. 2. When piping, provide sufficient lengths of tube, considering possible shrinkage. 3. When Tubes are inserted into Push-In Fitting, make sure that cut end surface of Tubes are right angle, without any scratches on the surface and deformations. 4. Note that the effective cross-section area varies by tube length. Refer to Effective Area of Piping in Tube Performance . ■ Minimum Bending Radius & Minimum Mounting Radius n= Deformation ratio (%). Standard: under 25% d= Tube O.D. L= Measured...

カタログの11ページ目を開く

Tube Series ■ Effective Sectional Area of Piping 1000 500 200 Effective Sectional Area (mm2) Tube Performance 100 50 Tube I.D. ø11 Tube I.D. ø9 Tube I.D. ø7.5 Tube I.D. ø6.5 Tube I.D. ø6(ø5.9) Tube I.D. ø5 Tube I.D. ø4 Tube I.D. ø3.48

カタログの12ページ目を開く

UE series 1 / 12ページ

カタログの抜粋

NIHON PISCO CO.のすべてのカタログと技術パンフレット

UE series
1 / 12ページ