カタログ >
NIHON PISCO CO., Ltd. >
Throttle (Needle) Valve PP Series

Throttle (Needle) Valve PP Series
1 / 15ページ

カタログの抜粋

CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Flow Control Valve for Clean Environment Throttle (Needle) Valve Copper alloy Non- Clean-room free material grease packaging option Chemical Industry Medical Industry Medicine Industry Food Industry (polypropylene) Body Material for Clean Environment. ● SUS304 for Seal Rubber. ● Oil-Free. PP Series Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series Fluid by Transparent Body Color. Pressure Gauge Series Check Valve Series Silencer

カタログの1ページ目を開く

Controller Series Throttle (Needle) Valve ■ Model Designation (Example) PJN Throttle (Needle) Valve PP Series 01 ⑥ Thread sealing option ④ Seal rubber material Union Straight ③ Thread size Thread size Metric thread (mm) Taper pipe thread Speed Controller Series Stainless Series PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series ④ Seal rubber material 　No code：EPDM 　F：FKM 　N：NBR ⑤ Packaging option 　No code：Standard package 　C：Clean-room package ⑥ Thread sealing option (taper thread only)

カタログの2ページ目を開く

■ Specifications Fluid medium Air / Water / Other chemicals (※1) 0 ～ 0.9MPa (at 0 ～ 20ºC) ※ 2 Operating temp. range 0~80℃ (Seal rubber NBR: 0~60℃ )（No freezing） MAKE-TO-ORDER PRODUCTS ■ Relation of Operating Temp. & Max. Operating Pressure Warning ※ 1. Make sure to follow the instructions below when the fluid medium is water or other chemicals. 1. Surge pressure must be controlled lower than max. operating pressure when using water or liquid as a fluid medium. 2.Be sure to place Insert Ring into the tube edge when using water or liquid as a fluid medium. 3. The specification above may not...

カタログの3ページ目を開く

Controller Series Throttle (Needle) Valve Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Detailed Safety Instructions 1. When controlling the speed of actuators, slowly release the air by adjusting the needle Manual” on page 23 to 27 and “Common Safety Instructions for Controllers” on page 367 to 368. Warning from a fully closed state. In case the needle is opened, actuator can move suddenly. Turn needle in the clockwise direction to close, and in the counterclockwise to open. 2. Do not swing or rotate resin body of the products by force. It may...

カタログの4ページ目を開く

■ How to insert and disconnect 1. How to insert and disconnect tubes CONTROLLER ① Tube insertion 　Insert a tube into Push-In Fitting up to the tube end. Lock-claws bite the tube and fix it automatically, then the elastic sleeve seals around the tube. 　Refer to “2. Instructions for Tube Insertion” under “Common Safety Instructions ② Tube disconnection 　The tube is disconnected by pushing release-ring to release Lock-claws. 　Make sure to stop air supply before the tube disconnection. MAKE-TO-ORDER PRODUCTS 2. How to tighten thread ① Tightening thread 　Use a spanner to tighten a...

カタログの5ページ目を開く

Controller Series PP Series PJNC Elbow Throttle (Needle) Valve Metric thread type Tube O.D. Model code øD 471 Speed Controller Series Stainless Series PP Series ※ 1. “L1” and “L2” are reference values for height dimensions after tightening taper thread. ※ 2. ④ in Model code / Replaced with “F” (FKM), or “N” (NBR) for Seal rubber material change ※ 3. ⑤ in Model code / Replaced with “C” for Clean-room package ※ 4. ⑥ in Model code / Replaced with “S” for Sealock, or “TP” for Seal tape on thread.

カタログの6ページ目を開く

PJNU Union Straight MAKE-TO-ORDER PRODUCTS ※ 1. ④ in Model code / Replaced with “F” (FKM), or “N” (NBR) for Seal rubber material change ※ 2. ⑤ in Model code / Replaced with “C” for Clean-room package PP Series Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series Pressure Gauge Series Check Valve Series

カタログの7ページ目を開く

Controller Series PP Series ■ Flow characteristic (Fluid: Air) Flow rate (l/min(ANR)) Union Straight Type Speed Controller Series PJNU 10 Control flow Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Stainless Series Control flow Flow rate (l/min(ANR)) Constant Flow Series Anti-spatter Series Control flow Flow rate (l/min(ANR)) Throttle (Needle) Valve Series Stainless Series Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) PJNC 4-01 Control flow 6-01 400 8-01 Flow rate (l/min(ANR)) Elbow type PJNC 4-M5 Control flow 6-M5 140 Flow rate (l/min(ANR)) Throttle...

カタログの8ページ目を開く

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

カタログの9ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

カタログの10ページ目を開く

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

カタログの11ページ目を開く