カタログ >
NIHON PISCO CO., Ltd. >
Speed Controller PP Series

Speed Controller PP Series
1 / 17ページ

カタログの抜粋

CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type Speed Controller for Clean Environment Speed Controller Copper alloy Non- Clean-room free material grease packaging option Chemical Industry Medicine Industry PP Series Anti-spatter Series (polypropylene) Material for Clean Environment. ● SUS304 ● EPDM for Seal Rubber (Option: FKM or NBR). Fluid by Transparent Body Color. Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series Packaging Option. Pressure Gauge Series Check Valve Series Silencer

カタログの1ページ目を開く

Controller Series Speed Controller ■ Model Designation (Example) PJS Speed Controller PP Series A ⑧ Packaging option ⑦ Thread sealing option ⑥ Seal rubber material ⑤ Check valve speciﬁcation Union Straight ③ Thread size Thread size Metric thread(mm) Taper pipe thread　 03 Control direction ■ Air from thread side is controlled. Air from tube side ■ Air from tube side is controlled. Air from thread Speed Controller Series is not controlled and flows out from thread side. Stainless Series side is not controlled and flows out from tube side. Solenoid valve Single-acting cylinder Control flow...

カタログの2ページ目を開く

Fluid medium Check valve cracking pressure 0~80℃ (Seal rubber NBR: 0~60℃ )（No freezing） MAKE-TO-ORDER PRODUCTS ■ Relation of Operating Temp. & Max. Operating Pressure Warning ※ 1. The specification above may not be applied, depending on the kind of mixed gases, etc. used as fluid medium. Contact us and make sure to use PISCO products after verifying their suitability on the user side. ※ 2. If operating temp. exceeds 20℃ , refer to the following chart “Relation of Operating Temp. & Max. Operating Pressure”. Operating temp. range Operating pressure range PP Series Anti-spatter Series ■...

カタログの3ページ目を開く

Controller Series Speed Controller ■ Standard Size List Connection: Thread ⇔ Tube Type Page Thread size PJSC Elbow Connection: Tube ⇔ Tube 12 PJSU Union Straight Detailed Safety Instructions Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Manual” on page 23 to 27 and “Common Safety Instructions for Controllers” on page 367 to 368. Warning 1. When controlling the speed of actuators, slowly release the air by adjusting the needle from a fully closed state. In case the needle is opened, actuator can move suddenly. Turn needle in the clockwise...

カタログの4ページ目を開く

■ How to adjust the speed 1. Speed adjustment of actuators ② Reducing speed 　Turn the needle in the clockwise direction when the speed is too fast. Make sure to tighten the locknut at the desired speed. The speed setting can ① Increasing speed 　Turn the needle in the counterclockwise direction from a fully closed state. The more the needle is opened, the faster the actuator moves. Make sure to tighten the locknut at the desired speed. The speed setting can be changed without tightening the locknut. be changed without tightening the locknut. ■ How to insert and disconnect MAKE-TO-ORDER...

カタログの5ページ目を開く

Controller Series PP Series PJSC Elbow Speed Controller Metric thread type Model code Stainless Series PP Series ※ 1. “L1” and “L2” are reference values for height dimensions after tightening taper thread. ※ 2. □ in Model code / Replaced with ” A” for Meter-out, “B” for Meter-in ※ 3. ⑥ in Model code / Replaced with “F” (FKM), or “N” (NBR) for Seal rubber material change (FKM is not available for low cracking pressure type.) ※ 4. ⑦ in Model code / Replaced with “S” for Sealock or “TP” for Seal tape on thread ※ 5. ⑧ in Model code / Replaced with “C” for Clean-room package PJSU Union Straight...

カタログの6ページ目を開く

■ Flow characteristic Elbow Flow rate (l/min(ANR)) Control flow Flow rate (l/min(ANR)) Control flow Flow rate (l/min(ANR)) Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Anti-spatter Series Quick Exhaust Valve Series Free flow Control flow Free flow Free flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Flow rate (l/min(ANR)) Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) MAKE-TO-ORDER PRODUCTS Free flow Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Flow rate (l/min(ANR))...

カタログの7ページ目を開く

Controller Series PP Series Elbow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Control flow Free flow Control flow Free flow Control flow Stainless Series Free flow Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Control flow Speed Controller Series Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Speed Controller

カタログの8ページ目を開く

Union Straight Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Control flow MAKE-TO-ORDER PRODUCTS Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Control flow Flow rate (l/min(ANR)) Control flow Flow rate (l/min(ANR)) PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Flow rate (l/min(ANR)) Anti-spatter Series Free flow Control flow Flow rate (l/min(ANR)) Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series Pressure Gauge Series Check Valve Series Silencer Serie

カタログの9ページ目を開く

Controller Series PP Series Union Straight Speed Controller Series Stainless Series PP Series Free flow Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Speed Controller

カタログの10ページ目を開く

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

カタログの11ページ目を開く