R series
1 / 16ページ

カタログの抜粋

FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Push-In Fitting Type for Swinging and Rotating Applications Rotary Joint Series Push-In Fitting for General Pneumatic Piping. ● Rotatable for Swinging and Rotating Applications. Rotary Series Twist-Proof Fitting Block and Connector Coupling Color

カタログの1ページ目を開く

Fitting Series FITTING Rotary Joint Series ■ Model Designation (Example) R Rotary Joint inch size ③ Thread size Thread size Taper pipe thread Standard Series Mini Series Stainless Series Chemical Series PP Series EG Series Anti-spatter ＆ Brass Series Die Temperature Control Minimal Series Stop Fitting Series Rotary Series

カタログの2ページ目を開く

Fluid medium Max. operating pressurev Max. vacuum Operating temp. range VALVE TUBE ■ Allowable rotation Tube O.D. Allowable rotation Lock-claws (Stainless steel) Release ring (POM) O-ring (NBR) Ball bearing Thread Body (Brass, chromium plating) Guide ring (Nickel-plated brass) Elastic sleeve (NBR) O-ring (FKM) Taper pipe thread: Sealock - coating Metric thread: With gasket (SUS304+NBR) Rotary Series Twist-Proof Fitting Block and Connector

カタログの3ページ目を開く

Fitting Series FITTING Rotary Joint Series Detailed Safety Instructions Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Manual” on page 23 to 27 and “Common Safety Instructions for Fittings” on page 33 to 35. 1. Avoid radial load. It may reduce the lifetime of the products. 2. Use polyurethane tube for the high rotation applications. Hard tubes like nylon base may cause radial load to the fitting. ■ Standard Size List Connection: Thread ⇔ Tube Type RC Straight 289 Standard Series Mini Series Stainless Series Chemical Series PP Series EG Series...

カタログの4ページ目を開く

Avoid radial load, since Rotary Joint series is designed small and light with the ultra small ball bearing and a shaft holder. Polyurethane Tube is recommended for the high rotation applications. VALVE TUBE 2. Combination example 3D m o v e m e n t s c a n b e a c h i e v e d b y t h e MAKE-TO-ORDER PRODUCTS combination use of straight and elbow types. 2. Not-recommended example If the tube moves as the right figure shows, use polyurethane tube or High Rotary Joint series. Nylon Tube Nylon Tube Rotary Series Twist-Proof Fitting Block and Connector Coupling Color Ca

カタログの5ページ目を開く

Fitting Series FITTING Rotary Joint Series ■ How to insert and disconnect 1. How to insert and disconnect tubes ① Tube insertion 　Insert a tube into Push-In Fitting up to the tube end. Lock-claws bite the tube and fix it automatically, then the elastic sleeve seals around the tube. 　Refer to “2. Instructions for Tube Insertion” under “Common Safety Instructions for Fittings”. ② Tube disconnection 　The tube is disconnected by pushing release-ring to release Lock-claws. 　Make sure to stop air supply before the tube disconnection. 2. How to tighten thread ① Tightening thread 　Use a spanner to...

カタログの6ページ目を開く

Metric thread type MAKE-TO-ORDER PRODUCTS Tube end Hex. Allowable rotation Rotating Torque Effective area Weight CAD C H (min-1) (N cm) (mm2) (g) file name ・ Tube O.D. Model code øD ※ 1. “L” is a reference value for height dimension after tightening taper thread. ※ 2. min-1：rotation per minute Rotary Series Twist-Proof Fitting Block and Connector Coupling

カタログの7ページ目を開く

Fitting Series Elbow Rotary Joint Series Metric thread type Tube O.D. Model code øD 293 Standard Series Mini Series Stainless Series Chemical Series PP Series EG Series Hex. Allowable rotation Rotating Torque Effective area Weight CAD ・ H (min-1) (N cm) (mm2) (g) file name 1.5 500 ※ 1. “L” is a reference value for height dimension after tightening taper thread. ※ 2.min-1：rotation per minute Anti-spatter ＆ Brass Series Die Temperature Control Minimal Series Stop Fitting Series Rotary Series CAD CAD data is available at PISCO website.

カタログの8ページ目を開く

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

カタログの9ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

カタログの10ページ目を開く

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

カタログの11ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a...

カタログの12ページ目を開く

R series 1 / 16ページ

カタログの抜粋

NIHON PISCO CO.のすべてのカタログと技術パンフレット

R series
1 / 16ページ