カタログ >
NIHON PISCO CO., Ltd. >
Multi-Circuit Rotary Block

Multi-Circuit Rotary Block
1 / 12ページ

カタログの抜粋

FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Multi-Circuit Block for Rotating Applications Multi-Circuit Rotary Block Make to Order ● Suitable for Low-Speed Rotating Applications like Index Table Rotary Series Twist-Proof Fitting Block and Connector Coupling Color Cap

カタログの1ページ目を開く

Fitting Series FITTING Multi-Circuit Rotary Block ■ Model Designation (Example) RB Multi-Circuit Rotary Block ② Joint thread size ① Number of circuits Code ② Joint thread size Thread size Taper pipe thread ■ Speciﬁcations Fluid medium 303 Standard Series Mini Series Stainless Series Operating temp. range ■ Construction of Multi-Circuit Rotary Block Rotary Block (Nickel-plated brass) Chemical Series PP Series EG Series Anti-spatter ＆ Brass Series Die Temperature Control Minimal Series Stop Fitting Series Rotary Series Fixed Block (Nickel-plated brass) ■ Applicable Tube and Related Products...

カタログの2ページ目を開く

Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Caution 1. When installing Rotary Block on index table, make Figure 1 Concentricity adjustment Dial gauge VALVE sure to adjust each axis (concentric of tolerance: max. Manual” on page 23 to 27 and “Common Safety Instructions for Fittings” on page 33 to 35. Detailed Safety Instructions 0.1mm). 　 This product does not have any groove to fix the center positioning. Use a dial gauge to fix it. Refer to figure 1. 2. This product permits some air leakage. Do not use it for the applications which require no...

カタログの3ページ目を開く

Fitting Series Multi-Circuit Rotary Block RB6-□□ Multi-Circuit Rotary Block Unit：mm Model code Standard Series Mini Series Stainless Series Chemical Series PP Series CAD Weight ※ 1 Allowable rotation Rotating torque Effective area (mm2) (g) (min-1) (N m) ø4 Fitting ø6 Fitting file name ・ ※ 1. Weight is Multi-Circuit Rotary Block unit only, not including fittings. ※ 2. See ※ 2 on the dimensional drawing. The outside diameter of RB6-M5 is columnar of ø 29mm. Dimension of Fixed Block is the same as RB6-M6. ※ 3. min-1：rotation per minute EG Series Anti-spatter ＆ Brass Series Die Temperature...

カタログの4ページ目を開く

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

カタログの5ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

カタログの6ページ目を開く

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

カタログの7ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a...

カタログの8ページ目を開く

Safety Instructions 7. Instructions for Tube Disconnection ① Make sure there is no air pressure inside of the tube, before disconnecting it. ② Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. By insufficient pushing of the releasering, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. 8. Instructions for Installing a fitting ① When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting...

カタログの9ページ目を開く

Fitting Series Common Safety Instructions for Fittings Before selecting or using PISCO products, read the following instructions. Read the detailed instructions for individual series as well as the instructions below. Warning 1. Do not use fittings with fluid medium other than air or water. (Water can be used with some series.) Contact us for using other kind of fluid medium except air and water. 2. o not use fittings except Anti-spatter, Brass and Brass Compression Fitting D series in a place where the flame and weld spatter is produced. There is a risk of causing fire by sparks. 3. As for...

カタログの10ページ目を開く

　● Table 1. Tube O.D. Tolerance Urethane tube ± 0.05mm ± 0.15mm ± 0.15mm ± 0.15mm ± 0.15mm ± 0.15mm ± 0.15mm ± 0.15mm MAKE-TO-ORDER PRODUCTS 2. Instructions for Tube Insertion ① Make sure that the cut end surface of the tube is at right angle without a scratch on the tube surface and deformations. 1.In case of using non-PISCO brand tubes, make sure the tolerance of the outer tube diameter is within the following limits of Table 1. ② When inserting a tube, the tube needs to be inserted fully into the push-in fitting until the tubing edge touches the tube end of the fitting as shown in the...

カタログの11ページ目を開く