JSC series
1 / 13ページ

カタログの抜粋

CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS Speed Control Valve for High Speed Cylinder Speed Controller ● Speed High Flow Control Valve for Actuator. 388 Speed Controller Series Stainless Series PP Series Anti-spatter Series Flow Type with Same Size as Speed Controller Series. Constant Flow Series Throttle (Needle) Valve Series for High Speed Cylinder. Selection of Body Color (light-gray). Stainless Series PP Series Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series Pressure Gauge Series Check Valve Series Silencer S

カタログの1ページ目を開く

Controller Series Speed Controller High Flow ■ Model Designation (Example) JS Speed Controller Type: C (Elbow) only High-ﬂow type ※ Model code without “H” is regarded as Speed Controller Series. “AG” is marked on the top of needle for High-flow type. Control direction: A (Meter-out) only※ ※ (“AG” is marked on the top of needle. Locknut color: Blue) ■ Air from thread side is controlled. Air from tube side is not controlled and flows out from thread side. Solenoid valve Control flow ② Thread size Thread size Taper pipe thread Speed Controller Series Free flow ■ Speciﬁcations Fluid medium...

カタログの2ページ目を開く

■ Construction (Elbow: JSC) Symbol CONTROLLER Tube End Needle (Nickel-plated brass) Locknut (Aluminum) Lock-claws (Stainless steel) Release ring (POM) Metallic body (Nickel-plated brass) Tube TUBE O-ring (NBR) Resin body (PBT) Guide ring (Nickel-plated brass) Sealock - coating Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Manual” on page MAKE-TO-ORDER PRODUCTS Detailed Safety Instructions 23 to 27 and “Common Safety Instructions for Controllers” on page 367 to 368. Warning 1. When controlling the speed of actuators, slowly release the air by...

カタログの3ページ目を開く

Controller Series Speed Controller High Flow ■ How to adjust the speed 1. Speed adjustment of actuators ① Increasing speed clockwise direction direction from a fully closed state. The more too fast. Make sure moves. Make sure to The speed setting can be changed without tightening the locknut. ■ How to insert and disconnect 1. How to insert and disconnect tubes ① Tube insertion 　Insert a tube into Push-In Fitting up to the tube end. Lock-claws bite the tube and fix it automatically, then the elastic sleeve seals around the tube. 　Refer to “2. Instructions for Tube Insertion” under “Common...

カタログの4ページ目を開く

JSC-H Elbow Hex. Weight CAD (g) file name H MAKE-TO-ORDER PRODUCTS Tube O.D. Model code øD ※ 1. “L1” and “L2” are reference values for height dimensions after tightening taper thread. ※ 2. □ in Model code / Replaced with “W” for Light-gray color. 392 Speed Controller Series Stainless Series PP Series Anti-spatter Series Constant Flow Series Throttle (Needle) Valve Series Stainless Series PP Series Anti-spatter Series Quick Exhaust Valve Series Exhaust Valve Series Fixed orifice Series Pressure Control er Series Pressure Gauge Series Check Valve Series Chart Characteristic chart page 3D 3D...

カタログの5ページ目を開く

Controller Series High Flow ■ Flow characteristic Elbow High Flow type Flow rate (l/min(ANR)) Control flow Flow rate (l/min(ANR)) Control flow Free flow Flow rate (l/min(ANR)) Control flow Free flow Flow rate (l/min(ANR)) Free flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Control flow Speed Controller Series Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Free flow Control flow Flow rate (l/min(ANR)) Flow rate (l/min(ANR)) Speed Controller

カタログの6ページ目を開く

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

カタログの7ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

カタログの8ページ目を開く

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

カタログの9ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a...

カタログの10ページ目を開く

JSC series 1 / 13ページ

カタログの抜粋

NIHON PISCO CO.のすべてのカタログと技術パンフレット

JSC series
1 / 13ページ