cylinder
22ページ

カタログの抜粋

Vacuum Pad Equipped with Cylinder & Vacuum Generator Vacuum Cylinder Cylinder with built-in Vacuum Generator self-retracts and lifts the object immediately after making contact with the object via compressed air supply. l selection of pad sizes, materials and cylinder storkes. ■ Pad size: ø4/6/8/10/15/20/30/40/mm ■ Pad material: Nitrile / Silicon / Fluorosilicon rubber ■ Cylinder stroke: 5, 10, 20 a

カタログの1ページ目を開く

Vacuum Cylinder ■ Model Designation (Example) VSPE ⑤ Port size and joint type ④ Pad material Vacuum Cylinder ① Pad size Code Stroke Code Type ④ Pad material and application Material Code Application Nitrile rubber N Cardboard Plywood Iron plate Food-related Other general work-pieces Silicone rubber S Semiconductors Taking out molded parts Thin work-pieces Food-related Fluorosilicone rubber FS Taking out molded parts ⑤ Port size and joint type Joint type Code O.D. x I.D. Pad size ø4mm ~ ø40mm  PISCO offers a plug--n adapter from

カタログの2ページ目を開く

■ Construction Ejector case (POM) Filter element Diffuser (Nickel-plated brass) Spring (Stainless steel) O-ring (NBR) Nut (Nickel-plated brass) Slide case (Aluminum) Seal rubber (NBR) Case support (Nickel-plated brass) Slide shaft (Nickel-plated brass) Soft type Pad ■ Characteristics of Pad Material Pad material Item Material code Cardboard Plywood Application Taking out molded parts Iron plate Thin work-pieces Taking out molded parts Other general work-pieces Black Color Surface hardness (Shore A ) Physical Proper ties Highest operating temp. Lowest operating temp. Acid resistance Alkali...

カタログの3ページ目を開く

■ Suction Force Regarding suction force of soft pad type, the calculated suction force (theoretical suction force x safety factor) may not be assured, due to the characteristics of vacuum pad, vacuum level, pad material and work-piece, etc. Select the proper item based on “Vacuum Pad Selection Guide”. Carry out any necessary evaluation with an actual system before approval. Detailed Safety Instructions Before using PISCO products, be sure to read “Safety Instructions” and “Safety Instruction Manual” and “Common Safety Instructions for Vacuum Pad” . Warning 1. Minimize the load on ejector...

カタログの4ページ目を開く

■ How to insert and disconnect 1. How to insert and disconnect tubes ① Tube insertion Insert a tube into Push-In Fitting up to the tube end. Lock-claws bite the tube and fix it automatically, then the elastic sleeve seals around the tube. Refer to “2. Instructions for Tube Insertion” under “Common Safety Instructions for Fittings” . ② Tube disconnection The tube is disconnected by pushing release-ring to release Lock-claws. Make sure to stop air supply before the tube disconnection. 2. How to fix cylinder In order to fix the cylinder, tighten the hexagonal nut with a spanner. Refer to the...

カタログの5ページ目を開く

Vacuum Cylinder ■ Vacuum Pad Dimension VP 8L□

カタログの6ページ目を開く

VSPE Vacuum Cylinder ø4 or ø6 L3

カタログの7ページ目を開く

Vacuum Cylinder Various material for suction cup PISCO offers Pad material Material code Food safe dissipative rubber Cardboard Chemical Conductive rubber (low resistance) Chloroprene rubber (sponge) Taking out General parts of Work-pieces Taking out molded parts environment molded parts semiconductors with rough Iron plate Thin work-pieces Iron plate High temp. Other general work-pieces Color Light brown Bellows Surface Physical Properties Soft Bellows Highest operating temp. Lowest operating temp. Acid resistance Alkali resistance Gasoline / Diesel oil Oil resistance Benzene / Toluene...

カタログの8ページ目を開く

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

カタログの9ページ目を開く

Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper usage of PISCO products such as exceeding the...

カタログの10ページ目を開く

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

カタログの11ページ目を開く

1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a countermeasure, material change from NBR to...

カタログの12ページ目を開く

Safety Instructions 7. Instructions for Tube Disconnection ① Make sure there is no air pressure inside of the tube, before disconnecting it. ② Push the release-ring of the push-in fitting evenly and deeply enough to pull out the tube toward oneself. By insufficient pushing of the releasering, the tube may not be pulled out or damaged by scratch, and tube shavings may remain inside of the fitting, which may cause the leakage later. 8. Instructions for Installing a fitting ① When installing a fitting, use proper tools to tighten a hexagonal-column or an inner hexagonal socket. When inserting...

カタログの13ページ目を開く

cylinder 22ページ

カタログの抜粋

NIHON PISCO CO.のすべてのカタログと技術パンフレット

cylinder
22ページ