カタログ >
NIHON PISCO CO., Ltd. >
2-Circuit Junction Block Series

2-Circuit Junction Block Series
1 / 16ページ

カタログの抜粋

FITTING CONTROLLER VALVE TUBE MAKE-TO-ORDER PRODUCTS 2-Circuit Junction Block for Pneumatic Piping 2-Circuit Junction Block Series ● Add-On ● Inserting Connection. Adjustable by Adding and Removing Blocks. Release-Ring Color Selection for Each Line. ● Usable for Cooling Down Piping. Block and Connector Coupling Colo

カタログの1ページ目を開く

Fitting Series FITTING 2-Circuit Junction Block ■ Model Designation (Example) MA 2-Circuit Junction Block Series 　106：106 series (Fixed type) 　107：107 series (Free type) ② Inlet-port tube dia. (※ Port type: A(Inlet port) only) Tube size ③ Outlet-port tube dia. (※.107 series Port type: except A(Inlet port)) Tube size 327 Standard Series Mini Series Stainless Series Chemical Series PP Series EG Series Anti-spatter ＆ Brass Series Die Temperature Control Minimal Series Stop Fitting Series Rotary Series Twist-Proof Fitting Block and Connector ④ Port type Code Inlet port Middle outlet port ⑤...

カタログの2ページ目を開く

Fluid medium Operating temp. range VALVE TUBE Warning ※ . Make sure to follow the instructions below when the fluid medium is water. 1. Surge pressure must be controlled lower than max. operating pressure when using water as a fluid medium. 2. Tap water can be used. Consult us for using other kind of water. 3. Be sure to place Insert Ring into the tube edge when using water as a fluid medium. ■ Construction (107 series: Middle outlet port) Release ring (POM) Guide ring (Nickel-plated brass) MAKE-TO-ORDER PRODUCTS Lock-claws (stainless steel) Tube end Elastic sleeve (NBR) Air Insert ring...

カタログの3ページ目を開く

Fitting Series FITTING 2-Circuit Junction Block ■ Standard Size List 106 series Type MA106 Inlet port Inlet-port tube dia. O.D. Outlet-port tube dia. O.D.(mm) Page (mm) 6 8 ● ● P.331 10 ● ● 12 MA106 Middle outlet port P.331 MA106 End outlet port P.331 107 series Type MA107 Inlet port MA107 Middle outlet port P.332 MA107 End outlet port P.332 ■ How to use 106 series and 107 series properly ■ As for 106 series, the position of the air outlet port is fixed, when connecting blocks. ■ As for 107 series, the position of middle and end outlet port is free to move, even after connecting the block....

カタログの4ページ目を開く

■ How to insert and disconnect 1. How to insert and disconnect tubes ① Tube insertion 　Insert a tube into Push-In Fitting up to the tube end. Lock-claws bite the tube and fix it automatically, then the elastic sleeve seals around the tube. 　Refer to “2. Instructions for Tube Insertion” under “Common Safety Instructions ② Tube disconnection 　The tube is disconnected by pushing release-ring to release Lock-claws. 　Make sure to stop air supply before the tube disconnection. MAKE-TO-ORDER PRODUCTS 2. How to fix ports ① Drill tapping holes for screw “M6” on the mounted side in advance. In order...

カタログの5ページ目を開く

Fitting Series ■ 106 series (Fixed type) MA106 Inlet port Stainless Series Mini Series Standard Series MA106 Middle outlet port Model code Chemical Series PP Series Minimal Series Stop Fitting Series Rotary Series Twist-Proof Fitting Anti-spatter ＆ Brass Series 3D 3D CAD data is available at PISCO website. CAD

カタログの6ページ目を開く

Model code MAKE-TO-ORDER PRODUCTS MA107 Middle outlet port Model code ■ 107 series (Middle and end outlet port / movable type) ※ . □ in Model code/ Replaced with “B” for release ring color Black & Black, “R” for Red & Red, No code for Black & Red (2ports per set.) Model code ※ . □ in Model code/ Replaced with “B” for release ring color Black & Black, “R” for Red & Red, No code for Black & Red (2ports per set.) 3D 3D CAD data is available at PISCO website. CAD

カタログの7ページ目を開く

Fitting Series ■ 107 series (Middle and end outlet port / movable type) MA107 Bracket for 107 series 2-10.5 333 Standard Series Mini Series Stainless Series Chemical Series PP Series EG Series Anti-spatter ＆ Brass Series Die Temperature Control Minimal Series Stop Fitting Series Rotary Series Twist-Proof Fitting Block and Connector 3D 3D CAD data is available at PISCO website. CAD CAD CAD data is available at PISCO websit

カタログの8ページ目を開く

Safety Instructions SAFETY Instructions 　This safety instructions aim to prevent personal injury and damage to properties by requiring proper use of PISCO products. 　Be certain to follow ISO 4414 and JIS B 8370 ISO 4414Pneumatic fluid power…Recomendations for the application of equipment to transmission and control systems. JIS B 8370General rules and safety requirements for systems and their components. This safety instructions is classified into “Danger”, “Warning” and “Caution” depending on the degree of danger or damages caused by improper use of PISCO products. Danger Hazardous...

カタログの9ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp Disclaimer 1. PISCO does not take any responsibility for any incidental or indirect loss, such as production line stop, interruption of business, loss of benefits, personal injury, etc., caused by any failure on use or application of PISCO products. 2. PISCO does not take any responsibility for any loss caused by natural disasters, fires not related to PISCO products, acts by third parties, and intentional or accidental damages of PISCO products due to incorrect usage. 3. PISCO does not take any responsibility for any loss caused by improper...

カタログの10ページ目を開く

Safety Instructions SAFETY INSTRUCTION MANUAL PISCO products are designed and manufactured for use in general industrial machines. Be sure to read and follow the instructions below. 1. Do not use PISCO products for the following applications. ① Equipment used for maintaining / handling human life and body. ② Equipment used for moving / transporting human. ③ Equipment specifically used for safety purposes. 1. Do not use PISCO products under the following conditions. ① Beyond the specifications or conditions stated in the catalog, or the instructions. ② Under the direct sunlight or outdoors....

カタログの11ページ目を開く

http://www.pisco.co.jp http://www.pisco.co.jp 1. Remove dusts or drain before piping. They may get into the peripheral machine / facilities and cause malfunction. 2. When inserting an ultra-soft tube into push-in fitting, make sure to place an Insert Ring into the tube edge. There is a risk of causing the escape of tube and a fluid leakage without using an Insert Ring. 3. The product incorporating NBR as seal rubber material has a risk of malfunction caused by ozone crack. Ozone exists in high concentrations in static elimination air, clean-room, and near the high-voltage motors, etc. As a...

カタログの12ページ目を開く