グループ: EVIDENT
カタログの抜粋
OLYMPUS -—- RBIS Your Vision, Our Future • 100% volume and surface coverage • Phased array and eddy current array testing system • High throughput
カタログの1ページ目を開くOlympus’ turnkey industrial solutions are adaptable to fit the needs of each customer. Our high-quality inspection solutions use ultrasonic phased array probes integrated into fully automated testing systems to meet even the most stringent requirements for volume and surface inspections. Our systems enable customers to meet strict quality control standards while maintaining productivity. Project-Based Turnkey Solutions: • Dedicated project management • Electronic instrumentation and probes • Advanced software • Mechanical equipment • Water management system • Commissioning • Training and...
カタログの2ページ目を開くThe inspection head is mounted on a carriage that travels on a gantry portal along the length of the inspected billet while the billet is being rotated. Air cylinders are used to move the wedges down at the beginning of the inspection sequence and up at the end of the cycle. Probes are mounted in wedges that have many degrees of freedom and their own pneumatic suspension, ensuring optimal coupling despite variations in the straightness of the billet. Phased array probe wedges also have their own water couplant supply. The wedge design enables high repeatability of detection. Phased Array...
カタログの3ページ目を開くPhased Array Acquisition Unit The QuickScan™ PA 32:256 module is a phased array acquisition unit developed by Olympus for industrial inspection systems. The acquisition unit meets IP55 standards and was specifically designed for easy integration into industrial environments. The unit is managed by QuickView™ advanced software designed for ultrasonic inspection. Advanced Software Olympus’ advanced QuickView software makes it easy to set up the system, acquire data, and manage data. Surface Defect Inspection The solution offered by Olympus for detecting surfacebreaking defects on...
カタログの4ページ目を開くSTANDARD PRODUCT RANGE Diameter Length INSPECTION COVERAGE Volume and Surface Resolution DATA PRESENTATION Real-Time Inspection Results Parameter Setup Inspection Layout INSPECTION MODES C-scan, strip charts, and alarms A-scan, B-scan 20 different user-configurable layouts Typical Inspection PA Modes Longitudinal waves, shear waves: 1st half, 2nd half, multizone DETECTION CAPABILITIES FOR TYPICAL REFERENCE DEFECTS Typical Defects FBH > 0.7 mm Notches > 0.2 depth, length >10 mm Signal-to-Noise Ratio (SNR) > 9 dB Report Types Inspection, calibration, and calibration-check user configurable...
カタログの5ページ目を開くEvident - Olympus Scientific Solutionsのすべてのカタログと技術パンフレット
-
39DL PLUS
12 ページ
-
Spotweld Transducers
2 ページ
-
72DL PLUS™
8 ページ
-
Magna-Mike™ 8600
4 ページ
-
DC1–DC5
5 ページ
-
45MG
12 ページ
-
35 RDC
2 ページ
-
OmniScan MX ECA
2 ページ
-
NORTEC™ Scanners
2 ページ
-
OmniScan® X3 64
8 ページ
-
IPLEX GX/GT
8 ページ
-
IPLEX Long Scope
4 ページ
-
RVI General Overview
12 ページ
-
IPLEX TX
4 ページ
-
IPLEX G Lite
8 ページ
-
IPLEX GAir
8 ページ
-
IPLEX NX
12 ページ
-
MXPLFLN Series
2 ページ
-
OLYMPUS Stream
16 ページ
-
LC35
4 ページ
-
DP74
8 ページ
-
DP28
8 ページ
-
SZX7
16 ページ
-
SZ61 SZ51 Brochure
24 ページ
-
SZX16 - SZX10
24 ページ
-
MX63/MX63L
20 ページ
-
GX53 Brochure
20 ページ
-
BXC Series Brochure
4 ページ
-
BX53M - BXFM Brochure
28 ページ
-
CIX100
16 ページ
-
STM7 Series
24 ページ
-
LEXT OLS5000
42 ページ
-
Vanta Overview
8 ページ
-
Vanta™ iX Systems
4 ページ
-
Vanta™ iX Brochure
4 ページ
-
NORTEC 600
7 ページ
-
Camera Overview
12 ページ
-
DSX1000 Brochure
40 ページ
-
72DL PLUS
8 ページ
-
SZX-AR1
12 ページ
-
PRECiV 1.2 Brochure
20 ページ
-
Vanta GX Brochure
4 ページ
-
27MG
4 ページ
-
BondMaster 600
8 ページ
-
EdgeFORM™
2 ページ
-
OpenView SDK
3 ページ
-
Mini_Wheel_Encoder
2 ページ
-
OmniScan MX
12 ページ