カタログ >
COHERENT >
HyperRapid NX

HyperRapid NX
1 / 4ページ

カタログの抜粋

HyperRapid NX The Next Generation High Power Industrial Picosecond Laser HyperRapid NX is Coherent’s latest high power industrial picosecond FEATURES • Single wavelength output: 1064 nm, 532 nm, or 355 nm market with the latest technological innovations. • High power and burst mode for high throughput at significantly reduced TCO HyperRapid NX delivers over 250 µJ pulse energy with 10 ps duration • High energy at high repetition rates up to 1 MHz laser platform. It combines over 15 years of experience pioneering this at repetition rates up to 1 MHz. Output power is over 100W in the IR, 50W in the visible and 30W in the UV. These performance levels help reducing the Total Cost of Ownership for a production process in micromachining applications, for instance by simultaneously feeding 2 work stations within one machine. HyperRapid NX enables the most advanced applications with stateof-the-art pulse control and synchronization features. Pulses can be triggered on-demand with low jitter (<25 ns) and trigger-to-pulse delay. The fast process shutter allows both on/off control and energy attenuation for each individual pulse. Burst mode can be selected to determine how many 10 ps-pulses with 25 ns separation should be released in an envelope. Processing with bursts enhances the ablation rate on many materials and increases the process efficiency. The HyperRapid NX laser head is a self-contained system where all optical elements, control electronics and thermo-mechanical management are integrated. Its compact, lightweight design complies with state-of-the-art international safety regulation. Choose HyperRapid NX and be part of the industrial photonics revolution. • Time and amplitude control of each individual pulse • Extended lifetime performance, also at high power in the UV • Compact and light weight, same interfacing for all models APPLICATIONS • Cutting and drilling of strengthened glass, sapphire, ceramics and other tough materials, also composites • Cutting, drilling, selective removal of complex composite structures from dissimilar materials, including oxides, plastics, organics • Micromachining and structuring of large surfaces with line focusing o

カタログの1ページ目を開く

1 At lowest amplifier pulse repetition rate, unless stated otherwise. 2 Maximum output power (variable attenuator and process shutter at maximum transmission). 3 After warm-up time. 4 Steady-state (no pulse gating or change of pulse repetition rate). 5 Single-pulse operation (burst number = 1). 6 At 500 kHz. 7 Over 8 hours, ± 1°C ambient temperature. 8 With 5 pulses in the burst, at the lowest burst mode operation range frequency. 9 (Pulse repetition rate) x (number of burst) cannot exceed 5 MHz.

カタログの2ページ目を開く

TYPICAL PERFORMANCE CHARTS Average Power: Specification Points and Typical Curves Single Pulse Energy: Specification Points and Typical Curves 280 Pulse Repetition Frequency (kHz) Pulse Repetition Frequency (kHz) TYPICAL MANUFACTURING DATA FOR HyperRapid NX 355-30 (30W UV) HyperRapid NX is able to deliver cutting-edge performance in volume. Manufacturing data shows the excellent performance and reliable consistency across a large number of laser systems. Beam Circularity SmartPulse™: Placing You in the Driver’s Seat Dynamic Pulse Train Modulation HyperRapid NX architecture gives you full...

カタログの3ページ目を開く

MECHANICAL SPECIFICATIONS Laser Head Beam Output Required Space for Service Side View Beam Height Front View Rear View Required Space for Cables and Tubes Bottom View Coherent, Inc., 5100 Patrick Henry Drive Santa Clara, CA 95054 p. (800) 527-3786 | (408) 764-4983 f. (408) 764-4646 tech.sales@Coherent.com www.Coherent.com Coherent follows a policy of continuous product improvement. Specifications are subject to change without notice. Coherent offers a limited warranty for all HyperRapid lasers. For full details of this warranty coverage, please refer to the Service section at...

カタログの4ページ目を開く

HyperRapid NX 1 / 4ページ

カタログの抜粋

COHERENTのすべてのカタログと技術パンフレット

HyperRapid NX
1 / 4ページ