カタログ >
CKD >
【NEW】ABP2-HP1 Series Specifications・How to order・Dimensions

【NEW】ABP2-HP1 Series Specifications・How to order・Dimensions
1 / 7ページ

カタログの抜粋

【NEW】ABP2-HP1 Series Specifications・How to order・Dimensions - 1

Working fluid From a primary pressure of +0.1MPa to twice the primary pressure (max. 0.99MPa) Proof pressure Body port thread B ressure P gauge option Flow rate m3 /min(ANR) Refer to the flow characteristics in the graph on the right Boosting ratio Ambient temp Port size Weightkg Durability A Body port thread: Rc thread C Silencer option: Silencer (2 pcs. included) D Bracket option: None Rc thread NPT thread (made to order) G thread (made to order) No Pressure gauge (2 included) No Silencer (2 pcs. included) High performance silencer (2 pcs. included) Functions Internal air circuit diagram No Foot bracket (2 included) Base for mounting tank Pressure adjustment section Switching valve Booster chamber B IN side check valve P rimary pressure from IN passes through the check valve on IN side, and flows into booster chambers A and B.The primary pressure passes through the pressure adjustment section and switching valve, and flows into the driving chamber A. The piston moves to the left due to the pressure of the driving chamber A. Air in booster chamber A is compressed, passes through the check valve on the OUT side, and goes to the OUT side. W hen the piston reaches the stroke end, the changeover switch will be pushed, causing compressed air to be supplied to the switching valve pilot chamber and causing the switching valve to change over. Then the air in drive chamber A is exhausted, and the air is delivered to drive chamber B. T herefore, the piston moves to the right and air in booster chamber B is compressed, passes through the check valve at the OUT side and moves OUT. I f the above operations are repeated, pressure will be increased on the OUT side. Feedback pressure is transmitted to the pressure adjustment section due to the OUT side pressure, and boosting is continued until the pressure adjustment spring pressure is balanced. Silencer option Silencer option B Pressure gauge option: Pressure gauge (2 included) Bracket option Pressure gauge option 10 million cycles (nominal) (Refer to page 2) Selection switch Piston Body port thread Piston OUTside check valve Fixed orifice OUTside (Secondary pressure)

カタログの1ページ目を開く

【NEW】ABP2-HP1 Series Specifications・How to order・Dimensions - 2

Flow characteristics (with the 5 L air tank, equivalent to double the pressure increase) Pressure characteristics (Setting: primary pressure: 0.7MPa, secondary pressure: 1.0MPa, flow rate: 0.02m3/min (ANR)) Fluid characteristics show max. flow rate of air booster. If primary pressure is constant and secondary side flow rate is increased, max. secondary pressure decreases. Pressure characteristics show variation of set secondary pressure according to primary pressure variation. Note) Air booster needs approx. twice secondary side flow rate (max.) for primary side due to structure. Confirm...

カタログの2ページ目を開く

【NEW】ABP2-HP1 Series Specifications・How to order・Dimensions - 3

ABP2-HP1 Series Internal structure

カタログの3ページ目を開く

【NEW】ABP2-HP1 Series Specifications・How to order・Dimensions - 4

ABP2-HP1 Series Parts list Parts list Part No. Part name Part No. Part name Hexagon socket head cap screw Stainless steel Valve seat Aluminum alloy Spring washer Stainless steel Nitrile rubber Flat washer Stainless steel Cylinder body Aluminum alloy Stainless steel Aluminum alloy Nitrile rubber Side plate Aluminum alloy Nitrile rubber Nitrile rubber Detection valve body Aluminum alloy Nitrile rubber Wear ring Nitrile rubber Aluminum alloy Fixed orifice Stainless steel Hexagon socket set screw Stainless steel Stainless steel Stainless steel Hexagon socket set screw Stainless steel Oiles...

カタログの4ページ目を開く