カタログ >
CKD >
MV3QR

MV3QR
1 / 16ページ

カタログの抜粋

Technical data (1) Connector connection 1537 Manifold specifications sheet 1540 ik Always read the precautions in the Introduction and on page 1538 before use.

カタログの1ページ目を開く

Vacuum suction unit with emphasis on functions Fast and stable suction transport without positive pressure source Pressure sensor Vacuum filter PCD Silencer TotAirSys (Total Air) TotAirSys (Gamma) 3QR negative pressure switching unit Electrical response and pressure waveform Negative ON pressure Overshoot present Atmospheric pressure Vacuum release without positive pressure to prevent small chips from being blown away. Air blow-out 0!! * Small workpieces may be blown away Vacuum pressure Solenoid valve Ideal for suction transport of small articles! Solenoid valve Atmospheric pressure Vacuum...

カタログの2ページ目を開く

1 Vacuum burst 1 valve not required • Vacuum release without positive pressure to prevent small chips \ from being blown away. No further countermeasure required • No need for burdensome adjustment of burst pressure, flow rate and timing • Slimmer with no vacuum burst valve Speeds up the vacuum release in returning to positive pressure and shortens suction time with the use of solenoid valve with large flow rate Discrete chip tray 2 Footprint minimized • The footprint has been reduced by 44% and weight by 53% as compared with CKD's conventional unit with burst, making it ideal for...

カタログの3ページ目を開く

TotAirSys (Total Air) TotAirSys (Gamma) 1528CKD 3QR negative pressure switching unit MV3QRA/MV3QRB Series Self-reset, self-hold Unit common specifications 1 MPa = 10 bar (Self-hold) Connection circuit diagram

カタログの4ページ目を開く

Wiring method for pressure sensor Analog output voltage - pressure characteristics 4GA/B M4GA/B MN4GA/B 4GA/B (mastr) W4GA/B2 W4GB4 4TB Lead wire color and content 4F Weight Discrete valve Content Sensor Content Push-in fitting Model No. Manifold base Vacuum filter (attachment) Model No. ■ Weight calculation of negative pressure switching unit (Single valve unit weight + sensor weight + push-in fitting weight + vacuum filter weight) X Station No. + manifold base Example) When attaching self-reset, quadruple manifold with pressure sensor, 94 fitting screw or 94 vacuum filter...

カタログの5ページ目を開く

TotAirSys (Total Air) TotAirSys (Gamma) [^Pressure sensor Manifold for negative pressure D type connector, no lead, with surge suppressor/indicator lamp Lead wire length Lead wire • 3QRA12/3QRB12 C type connector, with lead, with surge suppressor/indicator lamp D type connector, no lead, with surge suppressor/indicator lamp Lead wire length

カタログの6ページ目を開く

■ 2-position single (self-reset): grommet lead wire

カタログの7ページ目を開く

Dimensions (MV3QRA120-M5) ■ 2-position single (self-hold): C type connector (C2/C2*/C3)

カタログの8ページ目を開く

■2-position single (self-reset): grommet lead wire

カタログの9ページ目を開く

manual override Non-locking manual override Dimensions (MV3QRB120-M5) 2-position single (self-hold): C type connector (C2/C2*/C3) Lead wire (AWG#26, O.D. q>1.35) Length 300 to 2000 mm (C2/C2*/C3) 35.1 ■ D type connector (D2/D2*/D3) Lead wire (AWG#26, O.D. 91.35) Length 300 to 2000 mm (D2/D2*/D3) 2n-M1.7 mounting screws Torque 0.10 to 0.14 N-m

カタログの10ページ目を開く

Non-locking manual override Dimensions (MV3QRB120-M5-V1) sensor equipped 2-position single (self-hold): C type connector (C2/C2*/C3) IP ■ D type connector (D2/D2*/D3) Lead wire (AWG#26, O.D. ^1.35) Length 3°° to 2°°° mm (D2/D2*/D3)

カタログの12ページ目を開く

MV3QRA/MV3QRB Internal structure and parts list Internal structure and parts list Sensor equipped solenoid valve manifold *1 Refer to direct acting 3-port valve 3QRA1/3QRB1 Series (page 1505) for internal structure and operating principle of the equipped solenoid valve. Solenoid valve C type/D type connector connection [Procedure] (1) Peel the sheath at the end of the lead wire by 2 to 3 mm. (2) Crimp the lead wire with a dedicated tool. (3) Insert the terminal into holes at both ends of the socket. (Note) Check the orientation for insertion. (4) Insert the socket into the solenoid valve...

カタログの13ページ目を開く

■ Tighten the solenoid valve with an appropriate torque when installing it. ■ Excessive tightening may damage the valve. Tightening torque: 0.10 to 0.14 N-m ■ Use a #0 screwdrive

カタログの14ページ目を開く

Product-specific cautions: Pressure sensor Design/selection Mounting, installation and adjustment How to replace pressure sensor A WARNING ■ Use this product in accordance with specifications. ■ Use for applications, or at load currents, voltages, temperatures, impacts or sites excluded from the specifications could result in damage or malfunctions. ■ This product is used for air and low vacuum. ■ The customer is responsible for checking safety and taking appropriate countermeasures for using fluids other than applicable fluids. Do not use this product for corrosive or flammable gases or...

カタログの15ページ目を開く

MV3QRA/MV3QRB Series Manifold specifications sheet How to fill out MV3QRA/B1 manifold specifications sheet Piping *1 Port size Connection Option Station No. Voltage Sensor *1: Mixing of the points specified above is not possible. Specify by model No.

カタログの16ページ目を開く