カタログ >
CKD >
High precision guided rodless cylinder SRG3

High precision guided rodless cylinder SRG3
1 / 22ページ

カタログの抜粋

High precision guided rodless cylinder SRG3 - 1

High precision guided rodless cylinder High precision guided rodless cylinder with integrated linear gide with a bore size of ø12 to ø25. This is optimal for precision transfer of a small parts. Downsized by integrating ine axis high precision guide on the side of rodless cylinder. Downsizing of device is achieved. Thin design like SRL3 CKD original flat rodless cylinder structure realizes ultra low table position. This enables thin design of devices. Also the design is based on SRL3 with same stroke length, making it easier to replace. Common port Common port (one end porting) and standard port (both ends porting) can be selected according to cylinder installation position. This contributes to downsizing of devices. Series variation Variation ans option selection table Safety precautions Selection guide Technical data Rodless type High precision guided rodless cylinder

カタログの1ページ目を開く

High precision guided rodless cylinder SRG3 - 2

High precision guided Rodless cylinder SRG3 Series Series Series variation SCP*2 Mounting style Table mounting thread size up Adjustable full-stroke bracket retrofitting Adjustable full-stroke Lside with shock absorber Adjustable full-stroke Rside with shock absorber Adjustable full-stroke both sides with shock absorber Both sides cushioned Standard stroke length (mm) Bore size Axial foot type Axial foot type Basic type Custom stroke length Rodless type High precision guided rodless cylinder

カタログの2ページ目を開く

High precision guided rodless cylinder SRG3 - 3

Variation and option combination table : Option : Available (custom order) : Available depending on conditions (consult with CKD) X : Not available Piping Screw Option Table mounting thread size up Port and cushion needle position specification Port and cushion needle position specification Port and cushion needle position specification Port and cushion needle position specification Port and cushion needle position specification Variation Double acting basic type Port thread For mounting adjustable stroke bracket afterwards Adjustable stroke H side Adjustable stroke R side Adjustable stroke...

カタログの3ページ目を開く

High precision guided rodless cylinder SRG3 - 4

Pneumatic components Safety precautions Always read this section before starting use. Refer to Intro 71 for the cylinder, and to Intro 78 for the cylinder switch. Individual precautions: rodless cylinder with high precision guide SRG3 Series Installation & Adjustment 1. Common CAUTION Please watch out when designing intermediate stop circuit. With a slit rodless cylinder such as the SRL3, some air leaks due to the structure, so braking cannot be controlled with the all ports closed 3-position valve, and it may not be possible to hold the table stop position. Use a double sided pressurized...

カタログの4ページ目を開く

High precision guided rodless cylinder SRG3 - 5

(4) Adjusting shock absorber Standard shock absorber Absorbed energy of shock absorber is adjusted by changing operational stroke length of shock absorber. Adjust the shock absorber working stroke by loosening the shock absorber lock nut and turning the shock absorber. After adjusting, tighten the shock absorber fixing nut with the tightening torque shown below. The shock absorber absorbs rated energy with the rated stroke. When the product is shipped, the shock absorber is installed with a slight margin to the stroke at the cylinder stroke limit. Absorbed energy is smaller than allowable...

カタログの5ページ目を開く

High precision guided rodless cylinder SRG3 - 6

Series Specific precautions Piping port position and operating direction. Basic circuit diagram Horizontal load CMK2 If piping is as shown in Fig. 1, equal pressure is applied on both sides of the piston when stopped, and the table does not pop out when restarting. CMA2 Bore size ø20 to 63. Option symbol (Blank, R, B, T) R indicates R side pressurized port and L indicates L side pressurized port. Before shipping, all plugs other than 1 each at R0 and L0 are sealed with plugs. Piping to other ports becomes possible by removing plug. Option symbol D not available. Bore size ø25 Option symbol...

カタログの6ページ目を開く

High precision guided rodless cylinder SRG3 - 7

Rodless cylinder with high precision guide SRG3 (standard type/with switch) Bore size Actuation Working fluid Max. working pressure MPa Min. working pressure MPa Withstanding pressure MPa Ambient temperature Port size Stroke tolerance mm Working piston speed mm/s Repeatability mm Cushion ø20 Double acting Compressed air 0.7 50 to 1000 (Note 1) ± 0.05 (if it has shock absorber) Air cushion Not required Use the turbine oil Class 1 ISOVG32 if lubricated. Lubricate continuously if lubricated. Note 1: Piston speed used with common port piping differs with the stroke. Contact CKD for details....

カタログの7ページ目を開く

High precision guided rodless cylinder SRG3 - 8

Switch specifications (M type switch) 1 Color/2 color indicator Descriptions Applications Output method Power voltage Load voltage Load current Light Leakage current M2V and M2H M2WV (2 color indicator type) PLC 10 to 30 VDC 5 to 20mA LED (ON lighting) Red/green LED (ON lighting) 1mA or less M3PH/M3PV (custom order) M3H and M3V PLC, relay, IC circuit or small solenoid valve NPN output Applications Power voltage Load voltage Load current Light Leakage current Leakage current Without indicator light PLC, relay 10 to 28 VDC 30 VDC or less 50mA or less 24 VDC ± 10% 10 to 30 VDC 5 to 20mA (Note...

カタログの8ページ目を開く

High precision guided rodless cylinder SRG3 - 9

With switch Bore size Port thread type Port thread type Cushion Both sides cushioned R side cushioned L side cushioned No cushion Blank Rc thread N NPT thread (ø20 and over) (custom order) G G thread (ø20 and over) (custom order) Mounting style Basic type Axial foot type Axial foot type Mounting style E Stroke length (mm) Bore size Stroke length Note 1 ø12 1 to 450 ø16 1 to 800 ø20 1 to 800 ø25 1 to 1000 Stroke length Switch model no. Note 2 · Note 3 Switch model no. Contact Reed Custom stroke length Lead wire Lead wire 2 color indicator type 1 color indicator type Note on model no....

カタログの9ページ目を開く

High precision guided rodless cylinder SRG3 - 10

How to order switch This is (SRL3 and common) Switch body mounting bracket Only switch body Mounting bracket (Note 2) M type switch T type switch Switch model no. (Previous page section F ) Switch model no. (Previous page section F ) (Note 1): Switch main body+mounting bracket does not include any lead wire holder. When lead wire holder is necessary, place an order separately. (Note 2): M type switch and T type switch has different brackets. (Note 3): Lead wire holder comes in a set of 10 pieces. Lead wire holder (Note 3) How to order discrete shock absorber SRL3 How to order repair parts...

カタログの10ページ目を開く