カタログ >
Bonfiglioli >
Parallel shaft gear units HDP series Bevel helical gear units HDO series

Parallel shaft gear units HDP series Bevel helical gear units HDO series
1 / 342ページ

カタログの抜粋

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 1

HDP-HDO series Parallel shaft gear units HDP series Bevel helical gear units HDO series HDP-HDO series We have a relentless commitment to excellence, innovation and sustainability. Our team creates, distributes and services world-class power transmission and drive solutions to keep the world in motion. HEADQUARTERS Bonfiglioli Riduttori S.p.A. Via Giovanni XXIII, 7/A 40012 Lippo di Calderara di Reno Bologna (Italy) tel: +39 051 647 3111 fax: +39 051 647 3126 bonfiglioli@bonfiglioli.com www.bonfiglioli.com

カタログの1ページ目を開く

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 3

GENERAL INFORMATION PARALLEL SHAFT GEAR UNIT SERIES HDP ATEX CONFIGURATION SELECTING THE GEAR UNIT GEAR UNITS ATEX CONFIGURATION 24 PARALLEL SHAFT GEAR UNITS SERIES HDP 28 17 Thermal capacity and rating charts 56 20.1 Motor mounting with bell housing 169 BEVEL HELICAL GEAR UNITS SERIES HDO 180 28 Thermal capacity and rating charts 216 31.1 Motor mounting with bell housing 329 BEVEL HELICAL GEAR UNITS SERIES HDO ATEX CONFIGURATION Revisions Refer to page 338 for the catalogue revision index. Visit www.bonfiglioli.com to search for catalogues with up-to-date...

カタログの3ページ目を開く

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 4

GENERAL INFORMATION 1 SYMBOLS AND UNITS OF MEASUREMENT Symbols Units of Description Measure Symbols Units of Description Measure An 1,2 [kN] Permissible axial force Thermal capacity with the PTFAN... [kW] contribution of forced ventilation Thermal capacity inclusive PTSR [kW] of contribution from cooling coil I - Cyclic duration factor Thermal capacity inclusive PTMCRA... [kW] of contribution from air/oil exchanger cooling unit ptmcrw... [kW] Thermal capacity inclusive of contribution from water/oil exchanger cooling unit Rc 1,2 [kN] Calculated radial force Permissible...

カタログの4ページ目を開く

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 5

GENERAL DESIGN FEATURES Gear units of the HDP and HDO series make optimum use of advanced design features, to offer: • Top torque density • Superior performance • Silent and vibration-free operation • Total ruggedness and reliability • Lifetime calculation in accordance with the applicable ISO and AGMA standards • Extensive customisation through a wide range of options offered in the catalogue (*) = Refer to the table “Selection of the optimal oil viscosity” for further information about minimum and maximum values of different oil viscosity and for using hydraulic circuits. For values of ta...

カタログの5ページ目を開く

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 6

INSTALLATION The following installation instructions must be observed: • Make sure that the gearbox is correctly secured to avoid vibrations. If shocks or overloads are expected, install hydraulic couplings, clutches, torque limiters, etc. • Before the eventual painting, the machined surfaces and the outer face of the oilseals must be protected to prevent paint drying out the rubber and jeopardising the oil-seal function. • Components to be keyed on to the gearbox output shafts should be machined to ISO H7 tolerances to prevent mating surfaces jamming and causing irreparable damage to the...

カタログの6ページ目を開く

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 7

LUBRICATION Refer to the User’s Manual available at www.bonfiglioli.com for indications about checking the oil level and its replacement. Do not mix mineral oils with synthetic oils and/or different brands. However, oil level should be checked at regular intervals and topped up as required. Check monthly if unit operates under intermittent duty, more frequently if duty is continuous. 5.1 Selection of the optimal oil viscosity (data relating to Shell Oils) Operating ambient temperature [C° | | Recommended operating limits ; ; Allowed operating limits. © Forbidden operating limits. * =...

カタログの7ページ目を開く

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 8

Lubrication for HDP-HDO series gearboxes The internal parts of HDP gearboxes are lubricated with a mixed immersion and splash system. Should the output speed be lower than 1 min-1 or the input speed greater than 1800 min-1, please contact Bonfiglioli Technical Service for advise. In mounting position V5, the top bearings in gearbox sizes HDP 60 to HDP 90 are pre-lubricated with grease and fitted with Nilos seals, unless the order specifies a forced lubrication system with mechanical pump (optional variants OP1, OP2) or electric pump (option MOP). If HDP 100 to 180 gearboxes have to be...

カタログの8ページ目を開く

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 9

STORAGE Observe the following instructions to ensure correct storage of the products: • Do not store outdoors, in areas exposed to weather or with excessive humidity. • Always place boards, wood or other material between the products and the floor. The gearboxes should not have direct contact with the floor. • In case of long-term storage all machined surfaces such as flanges, shafts and couplings must be coated with a suitable rust inhibiting product (Tectile 506 EH or equivalent). Furthermore gear units must be placed with the fill plug in the highest position and filled up with oil....

カタログの9ページ目を開く

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 10

SERVICE FACTOR Service factors listed here under are empirical values based on AGMA and ISO specifications as well as our experience for use in common applications. They apply for state of the art-designed driven machines and normal operating conditions. (*) - Indication of service factor based on FEM 1.001 classification available upon request. Consult factory. - Hoists for passengers lift: charted values not applicable. Consult factory.

カタログの10ページ目を開く

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 11

(*) - Indication of service factor based on FEM 1.001 classification available upon request. Consult factory. - Hoists for passengers lift: charted values not applicable. Consult factory.

カタログの11ページ目を開く

Parallel shaft gear units HDP series Bevel helical gear units HDO series - 13

SELECTING THE GEAR UNITSelection of the the Atex product must fit through the compilation of this selection form. For a safe selection it is strongly recommended to rely on the long time experience of the Bonfiglioli Technical Service Dept. G3D Bonfiglioli TECHNICAL DATA REQUIRED FOR THE SELECTION OF HDP - HDO Nr: Company / Customer Branch / Distributor Order quantity Delivery time Motor Type Rated motor power Motor power demand Input speed Pole number C1) GEARBOX Gearbox configuration Gear ratio CJ ATEX CONDITION [GROUPII] - 2014/34/EU Category: [2 = standard / 3 = special] Output torque...

カタログの13ページ目を開く