カタログ >
BCM SENSOR TECHNOLOGIES bv >
Model 1915/1995 Static Torque Transducers

Model 1915/1995 Static Torque Transducers
1 / 3ページ

カタログの抜粋

Model 1915/1995 Static Torque Transducers - 1

Features - strain gauge technology - range from 100 Ibin to 1000 kNm - accuracy up to 0.2 %fs - mild steel with nickel plated treatment (1915) 17-4PH construction (1995) - protection grade IP 66 - torque wrench and torsion measurement of shaft Description Based on BCM’s advanced strain gauge technology, 1915/1995 static torque transducers are made from either alloy steel (1915) or stainless steel (1995) and sealed to IP 66 protection grade. 1915/1995 static torque transducers are operated in the following way: one side of the transducer is fixed as the stationary part, while the other side is as motion part which intends to have torsion shift corresponding to the stationary part. These transducers are designed for symmetric use, i.e., use in measuring torques in both directions: clockwise (positive torque) and anti-clockwise (negative torque). 1915/1995 torque transducers can measure torque ranges from 100 lbin to 100 kNm with an accuracy up to 0.2%fs. On request, these transducers can be supplied as transmitters with conditioned signals such as 0~5 V can be obtained by integrating a signal conditioner PCB in the torque body. 1915/1995 torque transducers are widely used in torque wrench and torsion measurement of shaft. Electrical Connection *: For capacity > 5000F, contact sales for dimensions. BCM SENSOR TECHNOLOGIES BVBA Industriepark Zone 4, Brechtsebaan 2 B-2900 Schoten - Antwerpen, BELGIUM website: www.bcmsensor.com email: sales@bcmsensor.com

カタログの1ページ目を開く

Model 1915/1995 Static Torque Transducers - 2

The listed specifications and dimensions are subject to change without prior notice. *: On request, model 1915/1995 can be supplied as transmitter with conditioned output of 0~5 Vdc. Since torques in both clockwise and anti-clockwise can be measured, the zero-torque state of the torque transmitters can be set at 0 Vdc or 2.5 Vdc. In case the “zero output” is set to 2.5 Vdc, a asymmetric O/P can be obtained from the transmitter: the full scale O/P of the maximum positive torque will be 5 Vdc while the full scale O/P of the maximum negative torque is 0 Vdc. If the “zero output” is set to 0V,...

カタログの2ページ目を開く

Model 1915/1995 Static Torque Transducers - 3

Model 1915/1995 Static Torque Transducers Ordering Information 100 lbin 50 lbft 2500 lbft 1 kNm 250 lbin 100 lbft 5000 lbft 2 kNm position (pos.) 1: model 1915: made from mild steel 1995: made from 17-4PH stainless steel pos. 2: capacities 10 kNm 100 kNm 20 kNm 30 kNm 50 kNm 70 kNm pos. 6: mechanical interface Refer to the dimensions on the datasheets. Pos. 6 can be omitted from the ordering code. pos. 7: electrical interface cable, code = diameter(0)/number of conductors/cable jacket/cable length 5/4/PVC/1 = 05 mm, 4-conductors shielded, PVC, length = 1**m pos. 8: environment protection IP...

カタログの3ページ目を開く