Linear Strain Gauges for Bending Beam Force T ransducers
1 / 7ページ

お気に入りに追加する　

カタログの抜粋

Linear Strain Gauges for Bending Beam Force Transducers Description BCM SENSOR linear strain gauges are specially developed for manufacturing precision force transducers which employ bending beam working principle. For the purpose of this specific application, the linear strain gauges are temperature and creep compensated, and they can be either encapsulated or open-faced according to the requirement. The karma gauges can be manufactured with effective modulus compensation (E.M.C.). The E.M.C. gauges are mostly for manufacturing low-cost force transducers, because with the E.M.C. gauges the manufacturers can eliminate the use of compensation resistors and achieve the sensitivity compensation. For creep compensation, there are 18 creep codes: “N10, N9, N8, ..., O, ..., P5, P6, P7". The “N10” is the most negative creep code, while the “P7" is the most positive one. The “O” stands for a moderate creep code. For a specific strain gauge, see its available creep code in the table below. For customized creep code, consult BCM SENSOR. For more information on temperature compensation (S.T.C.), creep compensation, and E.M.C. of strain gauges, please refer to the corresponding articles respectively on the website of BCM SENSOR. Listed in the following table is the linear gauges available in stock for quick delivery. Ordering Information gauge length gauge pattern S.T.C. or E.M.C. number of gauges center distance of two grids backing material foil alloy creep code of gauges solder-pads gauge type ordering code example: material C: constantan K: karma E: encapsulated gauge O: open-faced gauge titanium martensitic SS, mild steel austenitic SS, copper aluminum magnesium plexiglass F: modified phenolic resin E: glass-fiber reinforced epoxy B: laminated polyetherketone I: polyimide resin A: advanced polyimide G: glass-fiber reinforced polyimide solder-pads finishing SP: naked solder pads SD: tined solder pads (solder dot) RL: silver-coated round copper leads (30mm) FR: silver-coated flat copper leads (30mm) CW: enamel insulated copper wires (30 mm) Note: (1) The center distance of two grids only applies to the half-bridge and full-bridge strain gauges. BCM SENSOR TECHNOLOGIES BVBA Industriepark Zone 4, Brechtsebaan 2 website: www.bcmsensor.com B-2900 Schoten - Antwerpen, BELGIUM email: sales@bcms

カタログの1ページ目を開く

Linear Strain Gauges for Bending Beam Force Transducers Technical Data AA Pattern Single Grid Linear Strain Gauges: Karma, 0.8mm, 350Ω Suggested Ordering Codes Schematic Diagram: Dimensions in mm and inch Gauge Length Grid Width Backing Length Backing Width Gauge Type Backing Material (Working Temp.) Creep Code Solder-pad Finishing E: encapsulated O: open faced 11 or M11: martensitic steel (e.g., mild steel, 17-4PH SS) 16 or M16: austenitic steel (e.g., 304 SS), or copper 23 or M23: aluminum SP: naked solder pads SD: solder dots RL: round copper leads FR: flat copper leads CW: enamel...

カタログの2ページ目を開く

Linear Strain Gauges for Bending Beam Force Transducers AA Pattern Single Grid Linear Strain Gauges: 1.5mm, 350Ω and 1000Ω Suggested Ordering Codes Schematic Diagram: Dimensions in mm and inch Gauge Length Grid Width Backing Length Backing Width Gauge Type Backing Material (Working Temp.) Creep Code Solder-pad Finishing 11 or M11: martensitic steel (e.g., mild steel, 17-4PH SS) 16 or M16: austenitic steel (e.g., 304 SS), or copper 23 or M23: aluminum Note: E.M.C. is only for karma (K) gauges. SP: naked solder pads SD: solder dots RL: round copper leads FR: flat copper leads CW: enamel...

カタログの3ページ目を開く

Linear Strain Gauges for Bending Beam Force Transducers AA Pattern Single Grid Linear Strain Gauges: 3.2mm, 350Ω, 700Ω and 1000Ω Suggested Ordering Codes ECF-350-3.2AA-(11)-O-SP ECF-350-3.2AA-(23)-O-SP ECF-700-3.2AA-(11)-O-SP ECF-700-3.2AA-(23)-O-SP EKF-1000-3.2AA-(11)-O-SD EKF-1000-3.2AA-(23)-O-SD Schematic Diagram: Dimensions in mm and inch Gauge Length Grid Width Backing Length Backing Width Note: Previously the gauge length of these gauges were indicated as “3” instead of “3.2”. For instance, the ordering codes were: ECF-350-3AA-(11)-O-SP EKF-1000-3AA-(11)-O-SP Gauge Type Backing...

カタログの4ページ目を開く

Linear Strain Gauges for Bending Beam Force Transducers AA Pattern Single Grid Linear Strain Gauges: Karma, 3.2mm, 2000Ω Suggested Ordering Codes Schematic Diagram: Dimensions in mm and inch Gauge Length Grid Width Backing Length Backing Width Gauge Type Backing Material (Working Temp.) Creep Code Solder-pad Finishing 11 or M11: martensitic steel (e.g., mild steel, 17-4PH SS) 16 or M16: austenitic steel (e.g., 304 SS), or copper 23 or M23: aluminum SP: naked solder pads SD: solder dots RL: round copper leads FR: flat copper leads CW: enamel insulated copper wires E: encapsulated O: open...

カタログの5ページ目を開く

Linear Strain Gauges for Bending Beam Force Transducers AA Pattern Single Grid Linear Strain Gauges: 3.8mm, 350Ω, 700Ω, and 1000Ω Suggested Ordering Codes Schematic Diagram: Dimensions in mm and inch Gauge Length Grid Width Backing Length Backing Width Gauge Type Backing Material (Working Temp.) Creep Code Solder-pad Finishing 11 or M11: martensitic steel (e.g., mild steel, 17-4PH SS) 16 or M16: austenitic steel (e.g., 304 SS), or copper 23 or M23: aluminum Note: E.M.C. is only for karma (K) gauges. SP: naked solder pads SD: solder dots RL: round copper leads FR: flat copper leads CW:...

カタログの6ページ目を開く

Linear Strain Gauges for Bending Beam Force Transducers FB Pattern Dual-Grid Linear Strain Gauges: 2.1mm, 350Ω and 1000Ω Suggested Ordering Codes Schematic Diagram: Dimensions in mm and inch Gauge Length Grid Width Backing Length Backing Width Gauge Type Backing Material (Working Temp.) Creep Code Solder-pad Finishing 11 or M11: martensitic steel (e.g., mild steel, 17-4PH SS) 16 or M16: austenitic steel (e.g., 304 SS), or copper 23 or M23: aluminum Note: E.M.C. is only for karma (K) gauges. E: encapsulated O: open faced SP: naked solder pads SD: solder dots RL: round copper leads FR: flat...

カタログの7ページ目を開く

BCM SENSOR TECHNOLOGIES bvのすべてのカタログと技術パンフレット

1. 

   EPS200-series

   3 ページ

2. 

   model 328s

   2 ページ

3. 

   664F(C)

   3 ページ

4. 

   101B(A19F)

   4 ページ

5. 

   101B(A12.6H)

   4 ページ

6. 

   101B(a19L)

   4 ページ

7. 

   Model 101B (a19D)

   3 ページ

8. 

   Model 1915/1995 Static Torque Transducers

   3 ページ

9. 

   Model 1966/1996

   3 ページ

10. 

    Model 1811

    3 ページ

11. 

    Model JB04 load cell junction Boxes

    1 ページ

12. 

    WD 21 Weighing indicator

    1 ページ

13. 

    153T

    3 ページ

14. 

    670F

    3 ページ

15. 

    725F

    4 ページ

16. 

    FD101

    3 ページ

17. 

    119B

    3 ページ

18. 

    1915/1995 Static Torque Transducers

    3 ページ

19. 

    1811 Non-Contact Rotary Torque Transducers

    3 ページ

20. 

    UG Force Transducers With Overload Protection

    4 ページ

21. 

    2911 Tensile & Compression Force Transducers

    3 ページ

22. 

    156K/159K Miniature Single Bending Beam Force Transducers

    3 ページ

23. 

    159A Miniature Single Bending Beam Force Transducers

    3 ページ

24. 

    1416 Rocker Pin Compression Load Cells

    3 ページ

25. 

    1312/1392 Shear-Web Compression And Tension Load Cells

    3 ページ

26. 

    1211/1291 Cylindrical Compression Load Cells

    3 ページ

27. 

    LV39 Liquid Level Transducers And Transmitters With Overvoltage Protection

    3 ページ

28. 

    LV36 Submersible Liquid Level Transmitters With Flush Diaphragm

    3 ページ

29. 

    LV16 Mini-Diameter Submersible Liquid Level Transducers

    3 ページ

30. 

    315T Smart Differential Pressure Transmitters

    2 ページ

31. 

    219D Differential Pressure Transmitters For Smart Valve Application

    3 ページ

32. 

    131C Inner Cavity Pressure Transmitters For General Purpose

    5 ページ

33. 

    105C Pressure Transmitters For Automotive Industry And Refrigerator

    3 ページ

34. 

    Model 1531

    3 ページ

35. 

    Model 2 9 6 5

    3 ページ

36. 

    M o d e l 1 9 1 6 / 1 9 9 6

    3 ページ

37. 

    Model 1815

    2 ページ

38. 

    Model 181 1

    3 ページ

39. 

    Model A3

    2 ページ

40. 

    Model A2

    2 ページ

41. 

    Model A1 Sensor Signal Conditioner

    2 ページ

42. 

    Model T3000

    5 ページ

43. 

    model 3911/3991

    3 ページ

44. 

    Model 1664 Single Point Load Cells

    3 ページ

45. 

    Model 1661

    3 ページ

46. 

    Model 1660

    3 ページ

47. 

    Semiconductor Strain Gauges

    5 ページ

48. 

    Diaphragm Strain Gauges for Pressure Sensors and Force T ransducers

    12 ページ

49. 

    Model TFS2100

    3 ページ

50. 

    Model TFS2200

    3 ページ

51. 

    Model TFS2000

    3 ページ

52. 

    Model L V66(a)/L V66(b)

    4 ページ

53. 

    Model L V38

    2 ページ

54. 

    Model L V39

    3 ページ

55. 

    Model L V37

    1 ページ

56. 

    Model L V36

    3 ページ

57. 

    Model L V35

    1 ページ

58. 

    Model L V16

    3 ページ

59. 

    Model 101B(f)

    6 ページ

60. 

    Model 101B(a15G)

    4 ページ

61. 

    Model 101B(a13H)

    4 ページ

62. 

    Model 101B(a12.6L)

    4 ページ

63. 

    Model 664F(b)

    3 ページ

64. 

    Model 664F(a)

    3 ページ

65. 

    Model 301B

    4 ページ

66. 

    Model 500G

    4 ページ

67. 

    Model 330B

    3 ページ

68. 

    Model SE106

    3 ページ

69. 

    Model SE105

    3 ページ

70. 

    Model SE103

    4 ページ

71. 

    Model SE102

    4 ページ

72. 

    Model SE101

    3 ページ

73. 

    BCM Load Cells

    2 ページ

74. 

    BCM Sensor Dies, OEM Pressure Sensors, OEM Differential Pressure Sensors & Transducers

    2 ページ

75. 

    BCM Pressure and Liquid Level Transducers and Transmitters

    2 ページ

76. 

    BCM Strain Gauges for Transducer Application and Stress Analysis

    2 ページ