カタログ >
Analog Devices/アナログ・デバイセズ >
ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0)

ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0)
1 / 24ページ

カタログの抜粋

ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0) - 1

750 MHz, 8 × 8 Analog Crosspoint Switch ADV3228/ADV3229 FEATURES FUNCTIONAL BLOCK DIAGRAM SER/PAR CLK 40-BIT SHIFT REGISTER WITH 4-BIT PARALLEL LOADING 8 (RESERVED) APPLICATIONS Routing of high speed signals including Video (NTSC, PAL, S, SECAM, YUV, RGB) Compressed video (MPEG, wavelet) 3-level digital video (HDB3) Data communications Telecommunications SET INDIVIDUAL OR RESET ALL OUTPUTS TO OFF 8 × 8 high speed, nonblocking switch array Pinout and functionally equivalent to the AD8108/AD8109 Drop-in compatible with ADV3224/ADV3225 16 × 8 array Complete solution Buffered inputs Programmable high impedance outputs 8 output amplifiers, G = +1 (ADV3228), G = +2 (ADV3229) Drives 150 Ω loads Operates on ±5 V supplies Low power: 0.5 W Excellent ac performance −3 dB bandwidth 200 mV p-p: 1200 MHz (ADV3228), 900 MHz (ADV3229) 2 V p-p: 750 MHz (ADV3228), 850 MHz (ADV3229) 0.5 dB flatness (2 V p-p): 250 MHz (ADV3228), 235 MHz (ADV3229) Slew rate: 2500 V/μs Serial or parallel programming of switch array 72-lead LFCSP (10 mm × 10 mm) GENERAL DESCRIPTION The ADV3228/ADV3229 are high speed 8 × 8 analog crosspoint switch matrices. They offer a −3 dB large signal bandwidth of 750 MHz (ADV3228) and a slew rate of 2500 V/μs. The ADV3228/ADV3229 include eight independent output buffers that can be placed into a high impedance state for paralleling crosspoint outputs to prevent off channels from loading the output bus. The ADV3228 has a gain of +1, the ADV3229 has a gain of +2, and they both operate on voltage supplies of ±5 V. Channel switching is performed via a serial digital control that can accommodate daisy chaining of several devices or via a parallel control to allow updating of an individual output without reprogramming the entire array. The ADV3228/ADV3229 are available in the 72-lead LFCSP package over the extended industrial temperature range of −40°C to +85°C. Rev. 0 Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2010 Analog Devices, Inc. All rights reserved.

カタログの1ページ目を開く

ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0) - 2

REVISION HISTORY 11/10—Revision 0: Initial Version

カタログの2ページ目を開く

ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0) - 3

ADV3228/ADV3229 SPECIFICATIONS VS = ±5 V, TA = 25°C, RL = 150 Ω, unless otherwise noted. Table 1. Parameter DYNAMIC PERFORMANCE −3 dB Bandwidth Gain Flatness Propagation Delay Settling Time Slew Rate NOISE/DISTORTION PERFORMANCE Differential Gain Error Differential Phase Error Crosstalk, All Hostile, RTO Off Isolation, Input to Output OIP2 OIP3 Output 1 dB Compression Point Input Voltage Noise Density DC PERFORMANCE Gain Error Gain Matching Gain Temperature Coefficient OUTPUT CHARACTERISTICS Output Resistance Output Disabled Capacitance Output Leakage Current Output Voltage Range...

カタログの3ページ目を開く

ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0) - 4

ADV3228/ADV3229 Parameter POWER SUPPLIES Supply Current Supply Voltage Range PSRR OPERATING TEMPERATURE RANGE Temperature Range θJA Test Conditions/Comments AVCC, outputs enabled, no load AVCC, outputs disabled AVEE, outputs enabled, no load AVEE, outputs disabled DVCC, outputs enabled, no load ±4.5 DC to 50 kHz, AVCC, AVEE f = 100 kHz, AVCC, AVEE f = 10 MHz, AVCC f = 10 MHz, AVEE f = 100 MHz, AVCC f = 100 MHz, AVEE f = 100 kHz, DVCC Operating (still air) Operating (still air)

カタログの4ページ目を開く

ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0) - 5

ADV3228/ADV3229 TIMING CHARACTERISTICS (SERIAL) Table 2. Parameter Serial Data Setup Time CLK Pulse Width Serial Data Hold Time CLK Pulse Separation, Serial Mode CLK to UPDATE Delay UPDATE Pulse Width CLK to DATAOUT Valid, Serial Mode Propagation Delay, UPDATE to Switch On or Off Data Load Time, CLK = 5 MHz, Serial Mode CLK, UPDATE Rise and Fall Times RESET Time Timing Diagram—Serial Mode t2 LOAD DATA INTO SERIAL REGISTER ON FALLING EDGE 1 = LATCHED UPDATE 0 = TRANSPARENT TRANSFER DATA FROM SERIAL REGISTER TO PARALLEL LATCHES DURING LOW LEVEL 09318-002 Figure 2. Timing Diagram, Serial Mode...

カタログの5ページ目を開く

ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0) - 6

ADV3228/ADV3229 TIMING CHARACTERISTICS (PARALLEL) Table 4. Parameter Parallel Data Setup Time Address Setup Time CLK Pulse Width Parallel Data Hold Time Address Hold Time CLK Pulse Separation UPDATE Pulse Width CLK, UPDATE Rise and Fall Times RESET Time 1 = LATCHED UPDATE 0 = TRANSPARENT Figure 3. Timing Diagram, Parallel Mode

カタログの6ページ目を開く

ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0) - 7

ADV3228/ADV3229 ABSOLUTE MAXIMUM RATINGS POWER DISSIPATION 6V AVEE < VIN < AVCC DGND < DIN < DVCC AGND AVEE < VOUT < AVCC Momentary Internally limited to 55 mA −65°C to +125°C −40°C to +85°C 150°C 300°C Packaged in the 72-lead LFCSP, the ADV3228/ADV3229 junctionto-ambient thermal impedance (θJA) is 29°C/W. For long-term reliability, the maximum allowed junction temperature of the die should not exceed 125°C; even temporarily exceeding this limit can cause a shift in parametric performance due to a change in stresses exerted on the die by the package. Exceeding a junction temperature of...

カタログの7ページ目を開く

ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0) - 8

AGND NC AVEE NC AVCC NC AVEE NC AVCC NC AVEE NC AVCC NC AVEE NC AGND DVCC PIN CONFIGURATION AND FUNCTION DESCRIPTIONS DGND RESET CE DATAOUT CLK DATAIN UPDATE SER/PAR A0 A1 A2 D0 D1 D2 D3 NC DGND DVCC NOTES 1. NC = NO CONNECT. DO NOT CONNECT TO THIS PIN. 2. EXPOSED PADDLE. THE EXPOSED METAL PADDLE ON THE BOTTOM OF THE LFCSP PACKAGE MUST BE SOLDERED TO THE PCB AGND FOR PROPER HEAT DISSIPATION AND FOR NOISE AND MECHANICAL STRENGTH BENEFITS. Description Analog Positive Supply. Input Number 0. Analog Negative Supply. Input Number 1. Input Number 2. Input Number 3. Input Number 4. Input Number 5....

カタログの8ページ目を開く

ADV3228/ADV3229: 750 MHz, 8 × 8 Analog Crosspoint Switch Data Sheet (Rev. 0) - 9

Mnemonic D3, D2, D1, D0 A2, A1, A0 SER/PAR UPDATE DATAIN CLK DATAOUT CE RESET EPAD Description Parallel Data Input. Parallel Output Address Input. Serial/Parallel Mode Select (Control Pin). Second Rank Write Strobe (Control Pin). Serial Data In (Control Pin). Serial Data Clock, Parallel First Rank Latch Enable (Control Pin). Serial Data Out. Chip Enable (Control Pin). Second Rank Reset (Control Pin). Exposed Paddle. The exposed metal paddle on the bottom of the LFCSP package must be soldered to the PCB AGND for proper heat dissipation and for noise and mechanical strength benefits.

カタログの9ページ目を開く