カタログ >
4B Braime Components >
ADB adjustable depth bearing temperature sensors

ADB adjustable depth bearing temperature sensors
1 / 5ページ

カタログの抜粋

ADB adjustable depth bearing temperature sensors - 1

Product Information ADB Series Temperature Sensor ADB Series – Cable Entry Adjustable Depth Bearing Temperature Sensor APPLICATION For use on any application where bearing temperature monitoring is desired or required. METHOD OF OPERATION The ADB series have been designed to allow the depth of the sensor to be adjustable depending on your application. A number of versions are available with probe lengths of 50, 100, 200 and 300 mm. The sensors screw directly into a bearing housing through a 1/4” BSPT threaded grease zerk. Each sensor is fitted with a grease zerk to allow lubrication of the bearing without the need for removal of the sensor. The ADB series have NTC or PT100 type thermistors which allow for continuous temperature monitoring. The sensor is supplied with a 3m attached cable and can be connected to a PLC or to a hazard monitoring system, such as 4B’s T500 Hotbus Elite, Watchdog Super Elite, or T400 NTC Elite. The connections are not polarity sensitive therefore special connection requirements are eliminated, and the cable can be extended in the field. ADB8 Sensor – Cable Entry (ATEX and IECEx Zone 20 Approved) FEATURES ► Adjustable Sensor Depth ► Screw in Positive Mount Installation ► Grease Zerk for Bearing Lubrication ► NTC or PT100 Thermistor - Continuous Temperature ► ATEX and IECEx Zone 20 Approved Part Number Thermistor Type ATEX Zone Note: 5m Cable Sensors are Available on Request Detailed specification, wiring diagrams and installation/operating instructions available upon request. Please refer to instruction manual for co

カタログの1ページ目を開く

ADB adjustable depth bearing temperature sensors - 2

カタログの2ページ目を開く

ADB adjustable depth bearing temperature sensors - 3

Product Information ADB Series Temperature Sensor ADB Series – Conduit Entry Adjustable Depth Bearing Temperature Sensor APPLICATION For use on any application where bearing temperature monitoring is desired or required. METHOD OF OPERATION The ADB series have been designed to allow the depth of the sensor to be adjustable depending on your application. A number of versions is available with probe lengths of 50, 100, 200 mm. The sensors screw directly into a bearing housing through the existing 1/8” NPT threaded grease zerk. Each sensor is fitted with a grease zerk to allow lubrication of...

カタログの3ページ目を開く

ADB adjustable depth bearing temperature sensors - 4

Product Information ADB Series Temperature Sensor Bearing Sensor on Belt Conveyor Installation of Bearing Temperature Sensor TECHNICAL SPECIFICATIONS ADB Series - Bearing Temperature Sensor Example of Bearing Failure Resistance at 25°C: Resistance at 60°C: Resistance at 90°C: Sensing Voltage: Current Draw: Fixing Thread: Minimum Temp: Maximum Temp: Resistance at -30°C: Resistance at 60°C: Resistance at 100°C: Sensing Voltage: Current Draw: Fixing Thread: Minimum Temp: Maximum Temp: 88.22 Ohms 123.24 Ohms 138.50 Ohms Via Transducer 1 ma 1/8" NPT -30°C 110°C Temperature Sensors can be used...

カタログの4ページ目を開く

ADB adjustable depth bearing temperature sensors - 5

Product Information ADB Series Temperature Sensor ADB Series – Accessories ADBW - Probe Depth Adjustment Tool APPLICATION This specially designed wrench will allow the installer to tighten the olive nut during installation. INSTALLATION INSTRUCTIONS 1.Remove the existing grease nipple from the bearing sensor. 2.Slacken the olive nut and remove the sensor probe. 3.Screw the sensor body in to the threaded hole in the bearing housing. 4.Re-insert the temperature probe in to the olive nut adjusting the depth to suit the bearing depth. 5.Tighten the olive nut using the recommended special...

カタログの5ページ目を開く