DP specification
7Pages

1. Dry cycle time accords with EUROMAP 6. 2. The mold-bearing capacity of moving platen is 2/3 of total mold weight. 3. The shot weight is calculated by GPPS and it is 0.92 times of the theoretical shot volume. 4. Three kinds of screws are available for each model and the medium one is standard on the machine. 5. The injection unit data are in international units and calculated as follows: theoretical shotvolume [cm3] x injection pressure [MPa]/100 S. Plasticizing capacity is calculated by GPPS (for the injection unit model 18050 and smaller ones) orPP (for injection unit above model 18050). 7. The blue and green words respectively represent the standard configuration of clamping unit and injection unit. 8. Because of constant technical improvement, the machine specifications are subject to change without notice.

1. Dry cycle time accords with EUROMAP 6. 2. The mold-bearing capacity of moving platen is 2/3 of total mold weight. 3. The shot weight is calculated by GPPS and it is 0.92 times of the theoretical shot volume. 4. Three kinds of screws are available for each model and the medium one is standard on the machine. 5. The injection unit data are in international units and calculated as follows: theoretical shotvolume [cm3] x injection pressure [MPa]/100 S. Plasticizing capacity is calculated by GPPS (for the injection unit model 18050 and smaller ones) orPP (for injection unit above model...

1. Dry cycle time accords with EUROMAP 6. 2. The mold-bearing capacity of moving platen is 2/3 of total mold weight. 3. The shot weight is calculated by GPPS and it is 0.92 times of the theoretical shot volume. 4. Three kinds of screws are available for each model and the medium one is standard on the machine. 5. The injection unit data are in international units and calculated as follows: theoretical shotvolume [cm3] x injection pressure [MPa]/100 S. Plasticizing capacity is calculated by GPPS (for the injection unit model 18050 and smaller ones) orPP (for injection unit above model...

1. Dry cycle time accords with EUROMAP 6. 2. The mold-bearing capacity of moving platen is 2/3 of total mold weight. 3. The shot weight is calculated by GPPS and it is 0.92 times of the theoretical shot volume. 4. Three kinds of screws are available for each model and the medium one is standard on the machine. 5. The injection unit data are in international units and calculated as follows: theoretical shotvolume [cm3] x injection pressure [MPa]/100 S. Plasticizing capacity is calculated by GPPS (for the injection unit model 18050 and smaller ones) orPP (for injection unit above model...

1. Dry cycle time accords with EUROMAP 6. 2. The mold-bearing capacity of moving platen is 2/3 of total mold weight. 3. The shot weight is calculated by GPPS and it is 0.92 times of the theoretical shotvolume. 4. Three kinds of screws are available for each model and the medium one is standard on the machine. 5. The injection unit data are in international units and calculated as follows: theoretical shotvolume [cm3] x injection pressure [MPa]/100 S. Plasticizing capacity is calculated by GPPS (for the injection unit model 18050 and smaller ones) orPP (for injection unit above model 18050)....

1. Dry cycle time accords with EUROMAP 6. 2. The mold-bearing capacity of moving platen is 2/3 of total mold weight. 3. The shot weight is calculated by GPPS and it is 0.92 times of the theoretical shot volume. 4. Three kinds of screws are available for each model and the medium one is standard on the machine. 5. The injection unit data are in international units and calculated as follows: theoretical shotvolume [cm3] x injection pressure [MPa]/100 S. Plasticizing capacity is calculated by GPPS (for the injection unit model 18050 and smaller ones) orPP (for injection unit above model...

1. Dry cycle time accords with EUROMAP 6. 2. The mold-bearing capacity of moving platen is 2/3 of total mold weight. 3. The shot weight is calculated by GPPS and it is 0.92 times of the theoretical shot volume. 4. Three kinds of screws are available for each model and the medium one is standard on the machine. 5. The injection unit data are in international units and calculated as follows: theoretical shotvolume [cm3] x injection pressure [MPa]/100 S. Plasticizing capacity is calculated by GPPS (for the injection unit model 18050 and smaller ones) orPP (for injection unit above model...