Xebec Diamond - 4 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

Catalogue excerpts

L XEBEC Diamond Lineup A ♦ Ideal for polishing extremely hard die and mold (especially materials harder than HRC57). 0 Finishing ribs after EDM o Finishing gates after EDM o Finishing and deburring in corners o Finishing and deburring in edges (§>For the Most Efficient Use... o The XEBEC Diamond can be used either dry or wet. o Coolant will increase efficiency. ♦Forming (Shaping the tip of a tool in accordance with the shape of a workpiece.) / Dressing <Stick type> o For easy and perfect forming / dressing, use an electrodeposited diamond stone. Do cutting <Rod type> o For easy and perfect forming / dressing, press a tool rotating in a hand grinder onto an electrodeposited diamond stone. Do cutting same way. ♦When Using with an ultrasonic tool o Please check the appropriate output. The tool may break or generate heat when the output is too large. o Please check the appropriate length. On an inappropriate length, the tool may not oscillate, or concentrated output may result in heat generation. oA bad clamp may concentrate output, resulting in heat generation. o Polishing capabilities may vary depending on the structure and method of the clamp in use; please read carefully the instructions of your supersonic tool. ♦When Using with a hand grinder c Ptease use below the maximum 30,000rpm. 0 Please use below 50mm full length. (If full length is more than 50mm, make sure to cut it below 50mm.) o Please wear protective eyeglasses, gloves and mask during use. /l\ Warning Please always follow the above instruction / • \ ■*9rmng ancj precautions in order to use the tools s XEBEC TECHNOLOGY CO.,LTD. Head Office 4-3-3 Koujimachi, Chiyoda-ku, Tokyo, Japan E-mail info@xebec-tech.co.jp your order: 4061-1 Minami-Minowa-mura, Kamiina-gun, Nagano, Japan

 Open the catalogue to page 1

For polishing hardened steel and cemented carbide XEBEC products are manufactured in a plant certified by ISO 9001, the international standard of quality control and assurance. - ancTsurface stability" Features of the XEBEC Diamond O Effeciently and cleanly polishes materials harder than HRC57 such as cemented carbide and hardened steel (SKD, DC, STAVAX, HPM, ASP, etc) O Both the Stick and the Rod types can be used to polish by the tip or the side OCan be formed into desired shape, such as a thinner tip O Suitable for removing EDM scales, polishing ribs and deburring from edges and corners OFar...

 Open the catalogue to page 2

KiiKC 'Diamond PollsliiiiK ^briurmiinut D 1. Polishing Performance by the Side Polishing Surface Comparison of Polishing Performance by the Side (Comparison with electroplated diamond file) WEDM Surface Surface Roughness polishing tlma(mln) polishing tlme(min) Surface Roughness polishing Llmefmin] polishing tlme(mtn) Surface Roughness Rmax polishing time(min) polishing time(min) -o XEBEC Diamond #200 (immt) polishing method : air tool, by the side, dry oThe graphs represent comparisons of polishing performance data between XEBEC Diamond and an electroplated diamond file, both #200, using both...

 Open the catalogue to page 3

Polishing Surface XEBEC Diamond WEDM Surface Surface Roughness polishing time(min) polishing tlme(mln) Surface Roughness Rmax polishing time(mln) polishing lime(nnin) polishing time(min) XEBEC Diamond #200 (immt) XEBEC Diamond #400 (immt) XEBEC Diamond #800 (immt) polishing method polishing area o The graphs for Cemented Carbide show the surface smoothness of a wirecut surface by using XEBEC Diamond #400 for 5 minutes, then #800 afterwards. oThe graphs for Hardened Steel show the surface smoothness of an EDM surface by using XEBEC Diamond #200 for the first 20 minutes, then #800 afterwards. o...

 Open the catalogue to page 4

All XEBEC TECHNOLOGY catalogues and technical brochures