Cutting Fiber for hand grinders - XEBEC TECHNOLOGY - (Version JPG) - Page n° 2 - PDF Catalogue | Technical Documentation

See other catalogues for XEBEC TECHNOLOGY

Deburring brush, Abrasive stone, Diamond, Floating tool-holder, Brush

Text version of the page

Grinding Performance

This is a comparison in grinding performance with diamond-ingrained abrasive nylon brush (#400)


	2.5	Surface Roughness
	2.5

	2.0
	2.0
1.5 's
1.5 's
		%		' il
i.o		I \
	0.5 0.0	\ \

		-I	^ ■ -'	> i>
				. . T
		30 60 90 Processing Time (see)

- XEBECCA1 1EB06M) [120Cf>pm] -XEBEC(A21EB06M) [120OCrpni]

- Abrasive Nyion Brush (Diamond#400) [120-X-pm]

Grinding Amount on Work

SS XEBEC Cutting Fiber improves surface smoothness in a short time.

8! XEBEC Cutting Fiber has superior grinding ability.

Processing Time (sec

A11 : Easy to fit, suitable for minute deburring.

A21 : More rigid than All, superior grinding efficiency.


Type Fnd	Product Code a 1 1 -FRORM	Fine Alumina Fiber Rod (color) A 1 1 (Dar])	Diameter & mm	Fine Alumina Fiber Rod Length O f) m m	Axis Core Diameter rh 3 m m
l_l IU End	r\ 1 1 1_LJ W vj 1V1 A21-EB06M	AA 1 1 V r\ CU/ A21 (White)	\jj \J Itili 1 <t> 6mm	L-\J \ 1 IM 1 20mm	\jj \j 111111 0 3mm

We are planning more additions and expansions to our lineup. Please visit our homepage for details.

[Pre-operation Inspections]

OConduct a test run for one minute before starting operation, and three minutes after changing the brush, to check for abnormalities, such as vibrations, or looseness of the brush axis joint. Even if there are no abnormalities during the test run. if you notice anything unusual such as vibrations during usage, please stop the operation immediately; breakage, deformation, or damage to such parts as the brush fiber rods and the axis.

[Maximum Revolutions]

OPIease use below the maximum revolutions of 12,000 rpm. Usage above the maximum may be dangerous because it may result in breakage to such parts as the brush fiber rods and the axis.

[Grinding Load, Depth of Cut]

OUsage with an excessive load (depth of cut) may not only give less than optimal results, but may also lead to breakage and scattering of fine alumina wire rods. They are especially prone to occur when processing edges and uneven areas; it is therefore necessary to process with low enough revolutions and a lighter load.

^Directions for Tool Usel>

[Polishing Flat Surfaces]

OAttach to a hand tool, and apply brush to work surface at an approximate 45 degrees angle.

O Apply as constant a load as possible with the brush to the work, and keep the depth of cut to a minimum (under 1mm).

[Polishing Edges and Deburring Uneven Areas]

OWhen polishing edges and deburring uneven areas, please work with lower revolutions and a lighter load. Also, please do not apply excessive pressure on the edges with the sides of the fiber rods.

[Bristle Length]

OWith usage over time, the overall length of the fine alumina fiber rods (bristle length) may shorten, resulting in more grinding power but less easy to fit; please adjust the grind and fit by decreasing the revolutions and load (depth of cut).

[Truing / Dressing]

OPress the tip of the rotating brush against some polishing paper stuck onto a board in order to adjust the form of the brush. Please do the same for the dressing as well.

[Dry / Wet Processing]

OXEBEC Cutting Fiber can be used for both dry and wet processing. Please use a dust collecting device to collect any dust produced during dry processing.

<CSafety measures for the Worker

[Protection]

OPIease always wear protective glasses, gloves, and masks when working. Also, wear long sleeves, and close all cuffs and hems of your outerwear so that your skin is not exposed.

[Beware of Grinding Powder]

OGrinding powder and burrs may scatter within the area around the work as the brush revolves; please use a dust collecting device to collect the dust that is produced during dry processing.

[Caution to Your Surroundings]

OThe area around your work is hazardous due to flying pieces of fiber rods from the brush and grinding powder; please enclose your working area to prevent other people from entering, or have the surrounding people wear protection as well.

f\ Warning

Please always follow the above instruction and precautions, and please wear your protective gear at all times, when using tool.

URL http://www.xebec-tech.co.jp

Please visit our homepage for details.

XEBEC

Your order

XEBEC TECHNOLOGY CO.,LTD.

4-3-3 Koujimachi Chiyoda-ku Tokyo, Japan Phone.+81-3-3239-3481 FAX.+81 -3-5211 -8964 URL http://www.xebec-tech.co.jp E-mail xebec@mba.sphere.ne.jp

4061-1 Minami-Minowa-mura Kamiina-gun Nagano.Japart

Phone.+81 -265-73-1523 FAX.+81 -265-77-1847

Head Office

Factory and R/D

Cutting Fiber for hand grinders - XEBEC TECHNOLOGY - #2

Deburring brush, Abrasive stone, Diamond, Floating tool-holder, Brush