See other catalogues for
WILKERSON
You may also be interested in
Text version of the page
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | Catalog 9EM-TK-190-2 | | Basic 1/8" Body | | |
| | | |
| | | Miniature Regulator RB3 Brass RA3 Aluminum | | |
| | | = "Most Popular" | | |
| | | |
| | | Specifications Flow Capacity* | | |
| | | 1/4 | | 14 SCFM (6.6 dm3/s) | | |
| | | |
| | | |
| | | Maximum Supply Pressure | | 300 PSIG (20.7 bar) | | |
| | | |
| | | Operating Temperature | | 40°to 125°F (4.4° to 51.7°C) | | |
| | | |
| | | |
| | | 1/8, 1/4 | | |
| | | Port Size | | NPT / BSPP-G | | |
| | | A. | | |
| | | |
| | | |
| | | Weight | | lb. (kg) | | 0.5 (0.23) | | |
| | | |
| | | |
| | | Inlet pressure 100 PSIG (6.9 bar). Secondary pressure 90 PSIG (6.2 bar). (flow at 25% pressure drop) | | |
| | | |
| | | B | | |
| | | Relieving | | |
| | | |
| | | |
| | | Materials of Construction Body RB3 RA3 | | |
| | | A | | |
| | | Brass Aluminum | | |
| | | |
| | | |
| | | | | | | | | | Bonnet | Acetal | | | | Diaphragm & Seals | Nitrile | | | | Valve Assembly & Bottom Plug | Brass | | | | Note: Panel Nut included, but not shown on dimensional drawing. | | | | | Note: 1.19" dia. (30.2) mm hole required for panel mounting. | | | | | A WARNING | | | | Product rupture can cause serious injury. Do not connect regulator to bottled gas. Do not exceed maximum primary pressure rating. | | | | | | | | | |
| | | ') mi RB3-02-F000 | | |
| | | Non-Relieving | | |
| | | |
| | | |
| | | Features | | |
| | | |
| | | Brass Body Construction Handles Water and Compressed Air Service Large Diaphragm to Valve Area Ratio for Precise Regulation and High Flow Capacity Spring Loaded Diaphragm High Flow: 1/4" -14 SCFM Panel Mount Nut Standard Two 1/8" Gauge Ports | | |
| | | |
| | | CAUTION: REGULATOR PRESSURE ADJUSTMENT - The working range of knob adjustment is designed to permit outlet pressures within their full range. Pressure adjustment beyond this range is also possible because the knob is not a limiting device. This is a common characteristic of most industrial regulators, and limiting devices may be obtained only by special design. For best performance, regulated pressure should always be set by increasing the pressure up to the desired setting. | | |
| | | |
| | | |
| | | 7/8" Hex Adjustment Knob | | |
| | | - 5/64" Hex Key Adjustment Screw | | |
| | | |
| | | |
| | | 1/8" Pilot Port | | |
| | | |
| | | 2.58 (65,5) | | |
| | | 1.09 (27,7) | | |
| | | |
| | | |
| | | 1.59 (40,4) | | |
| | | |
| | | Option R | | Option T | | Option Z | | |
| | | Dimensions | | |
| | | |
| | | |
| | | | | | | | | | | | | | Model 'nmme,s | A | B | C | D | E | | | | Brass Regulator - Miniature RB3-XX-XXXX | 1.56 (39.8) | 1.56 (39.8) | 2.56 (65) | .50 (12.7) | 3.06 (77.7) | | | | Aluminum Regulator - Miniature RA3-XX-XXXX | 1.56 (39.8) | 1.56 (39.8) | 2.56 (65) | .50 (12.7) | 3.06 (77.7) | | | | | | | | | | | | | |
| | | |
| | | WILKERSON | | |
| | | Pneumatic Division Richland, Michigan www.wilkersoncorp.com | | |
| | | B106 | | |
| | | |
| | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |