Batley Butterfly Valves - Weir Power & Industrial - #14

Text version of the page

14 Weir Power & Industrial First choice for power and industrial protection Batley Valve BV 6-0810 STEADSEAL BV20000 Nominal bore A B C1 C2 D E Wafer Flanged 150 * 76 140 205 175 200 * 89 152 235 207 250 * 114 165 275 237 300 * 114 178 320 285 350 * 127 190 347 312 400 * 140 216 375 340 450 * 152 222 390 377 500 * 152 229 470 437 600 * 178 267 480 490 700 * 229 292 515 528 750 * 229 292 540 562 800 * 241 318 575 607 900 * 241 330 620 681 1000 * 300 410 685 731 1050 * 300 410 715 755 1200 * 350 470 813 860 1400 * 390 530 890 950 1600 * 440 600 1040 1110 1800 * 490 670 1160 1220 2000 * 540 760 1280 1360 The table opposite represents the most common materials of construction but it should be noted that other materials and combinations of the above materials can be supplied. For use on corrosive media cast iron and carbon Steel bodies can be supplied with a number of different linings for protection, the most common of which are given below: Glass Flake Coating, Rubber lining both soft (neoprene) or hard (ebonite), Xylan resin bonded PTFE, Fusion bonded epoxy. In some circumstances valve bodies may be supplied in a fabricated mild steel construction in lieu of cast iron or cast carbon steel. * Dimension B will be to suit the dimensions of the mating flanges. Dimension F is dictated by the design shut off pressure when the valve is in the closed position. Alternative face to face dimensions can be supplied, such as AWWA C504, MSS SP67 or to the customers special requirements. Temperature Range °C Seal Materials General Service Continuous Intermittent Min Max Max Nitrile Water, sea water, oils, - 30 + 100 + 120 natural gas Neoprene Some freons, oxygen, - 30 + 100 + 120 some chemicals and solvents Butyl Water, air, acetone, esters - 30 + 100 + 110 Ethylene Propylene LP Steam, hot water, - 40 + 120 + 140 ketones, ester, alcohols Viton Gasolines, fuels, oils, solvents, - 15 + 200 aromatic hydrocarbons. NOTE - Not steam Carbon Steel 316 St Steel Al. Bronze Cast Iron Ductile Iron Body ASTM A216 WCB ASTM A351 CF8M BS 1400 AB2 EN 1561 EN 1563 Vane ASTM A216 WCB ASTM A351 CF8M BS 1400 AB2 EN 1561 EN 1563 Shaft 17-4 PH/316 SS 17-4 PH/316 SS Monel K500 Seal Nitrile/EPDM Nitrile/EPDM Nitrile/EPDM Dimensions Materials Seal Materials NOTES: Intermittent operating temperature means peaking above the maximum continuous temperature for one to two minutes occasionally but not on an hourly/daily frequency. The Rubber Selection table should only be used for general guidance and full details of temperatures, line fluids, pressures, frequency of operations, velocities and vacuum conditions etc., should be included with your enquiry to ensure that the correct seal selection is recommended. To suit actuator D C1 Ø ‘A’ Ø ‘B’ Ø ‘A Nom. bore’ Ø ‘B’ Mounting to suit actuator 4 Tapped or through locating holes to suit mating flange drilling Saw cut in line with vane To suit actuator Mounting to suit actuator Feet can be supplied if required Saw cut in line with vane Lifting holes E D C2 E