| | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | 01_Clamps 8/3/05 12:42 PM Page 14 | | |
| | | -e- | | |
| | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | Part | Model | | | | | +.000 | | | | | | | | | | | Number | Number | A | B | C | D | E -.002 | F | Gt | | | H* | I | J | | | | 590-38000 | #00 | 10.7 | 7.6 | 6.1 | 3.0 | 20.0 | 7.4 | 4.1 | M2 | on | 13.7 BHC | M2 | 4.1 | | | | 590-38050 | #0 | 21.8 | 16.0 | 15.0 | 5.9 | 29.72 | 12.4 | 8.0 | M3 | on | 20.95 BHC | M4 | 7.2 | | | | 590-38100 | #1 | 24.9 | 19.0 | 15.0 | 5.9 | 31.5 | 14.2 | 12.2 | M3 | on | 23.1 BHC | M6 | 11.2 | | | | 590-38150 | #2 | 24.9 | 19.0 | 15.0 | 5.9 | 37.5 | 20.0 | 13.5 | M3 | on | 29.0 BHC | M8 | 13.2 | | | | 590-38200 | #3 | 28.6 | 22.2 | 17.5 | 6.4 | 50.0 | 27.0 | 18.0 | M4 | on | 39.4 BHC | M10 | 16.3 | | | | 590-38250 | #4 | 31.8 | 25.4 | 20.6 | 6.4 | 56.0 | 35.3 | 23.0 | M4 | on | 45.5 BHC | M12 | 20.3 | | | | 590-38300 | #5 | 39.6 | 31.8 | 27.0 | 7.9 | 69.5 | 42.0 | 29.3 | M5 | on | 55.9 BHC | M16 | 21.4 | | | | 590-38350 | #6 | 39.6 | 31.8 | 27.0 | 7.9 | 75.5 | 51.5 | 29.3 | M5 | on | 63.9 BHC | M16 | 21.4 | | | | 590-38400 | #7 | 45.5 | 37.6 | 32.3 | 7.9 | 107.5 | 77.7 | 29.3 | M6 | on | 92.6 BHC | M16 | 19.3 | | | | 590-38450 | #8 | 45.5 | 37.6 | 32.3 | 7.9 | 132.9 | 103.0 | 29.3 | M6 | on | 118.06 BHC | M16 | 19.3 | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | Gt - Minimum diameter the "F" dimension can be machined or turned down to. H* - (3) Mounting Screws Included. | | |
| | | |
| | | MACHINING AND INSTALLATION | | |
| | | |
| | | Machine a pocket, in the fixture, for the close Tolerance "E" dimension and drill and tap mounting holes per "H" column. Drill and tap a hole from the "I" column in the centre of the pocket for the tapered screw. A recessed dowel pin may be installed into the flange for additional rigidity if required. | | |
| | | > Expand clamp approximately 0.1mm over relaxed diameter and machine to fit workpiece bore, either on lathe specifications or mill. > If machining the clamp on a lathe use the nut provided, on the back of the clamp, to tighten the tapered screw. This nut is used only to machine the clamp. | | |
| | | > | | |
| | | |
| | | > | | |
| | | |
| | | |
| | | Ordering Information | |
| | | |
| | | Tel: 0845 606 6677 • Fax: 0845 601 1173 If you can't find what you are Order online at www.wdsltd.co.uk • E-mail: sales@wdsltd.co.uk looking for industrial still call us. 14 WDS • Richardshaw Road • Grangefield Industrial Estate • Pudsey • Leeds LS28 6LE We also manufacture 'Specials' | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | |