EtherCAT Absolute Encoder
6Pages

{{requestButtons}}

Catalog excerpts

EtherCAT Absolute Encoder - 1

Content: Order Code Technical Data EtherCAT Interface Connection Technical Drawing

Open the catalog to page 1
EtherCAT Absolute Encoder - 2

mechanical multiturn, optical Sendix 5868 / 5888 (shaft / hollow shaft) The multiturn encoders Sendix 5868 and 5888 with second-generation EtherCAT interface and optical sensor technology are ideal for use in all applications with an EtherCAT interface. The data communication is based on CAN over EtherNet and ideally suited for use in real time applications. These encoders are available with a solid shaft up to a maximum of 10 mm or a blind hollow shaft up to 15 mm. EtherCAT.^ Conformance tested Reliable • EtherCAT conformance tested. • Integration of the latest slave - EtherCAT stack from...

Open the catalog to page 2
EtherCAT Absolute Encoder - 3

mechanical multiturn, optical Sendix 5868 / 5888 (shaft / hollow shaft) Mounting accessory for hollow shaft encoders Dimensions in mm [inch] Cylindrical pin, long for flange with spring element (flange type 1 + 2) 8.0010.4700.0000 with fixing thread Connection technology Order no. Cordset, pre-assembled M12 male connector with external thread for port IN and port OUT, 4-pin K4P2M-S-M12-CAT 2 m [6.56'] M12 female connector with coupling nut for power supply, 4-pin K4P2M-S-M12 Mechanical characteristics Interface characteristics EtherCAT Maximum IP65 up to 70°C [158°F] 9000 min-1, 7000 min-1...

Open the catalog to page 3
EtherCAT Absolute Encoder - 4

Sendix 5868 / 5888 (shaft / hollow shaft) EtherCAT Standard mechanical multiturn, optical General information about CoE (CAN over EtherNet) The EtherCAT encoders support the CANopen communication profile according to DS301. In addition device-specific profiles like the encoder profile DS406 are available. Scaling, preset values, limit switch values and many other parameters can be programmed via the EtherCAT bus. When switching the device on, all parameters are loaded from an EEPROM, where they were saved previously to protect them against power-failure. The following output values may be...

Open the catalog to page 4
EtherCAT Absolute Encoder - 5

mechanical multiturn, optical Sendix 5868 / 5888 (shaft / hollow shaft) Dimensions shaft version, with removable bus terminal cover Dimensions in mm [inch] Clamping flange, 0 58 [2.28] Flange type 1 and 3 Square flange, EH 63.5 [2.5] Flange type 5 and 7

Open the catalog to page 5
EtherCAT Absolute Encoder - 6

mechanical multiturn, optical Sendix 5868 / 5888 (shaft / hollow shaft) Dimensions hollow shaft version (blind hollow shaft), with removable bus terminal cover Dimensions in mm [inch] Flange with spring element, long Flange type 1 and 2 2 Slot spring element recommendation: cylindrical pin DIN 7, 0 4 [0.16] 2 3 x M3, 5.5 [0.22] deep 2 Recommended torque for the clamping ring 0.6 Nm Flange with stator coupling, 0 63 [2.48] Flange type 5 and 6 2 Recommended torque for the clamping ring 0.6 Nm Flange with stator coupling, 0 65 [2.56] Flange type 3 and 4 2 Recommended torque for the clamping...

Open the catalog to page 6

All WayCon Positionsmesstechnik GmbH catalogs and technical brochures

  1. LVIG SERIES

    5 Pages