Long Range Draw Wire Sensor SX135 up to 42.5 m
15Pages

Technical Data Digital WCAN 5 Series SX135 Key-Features: - Measurement ranges from 10.0 to 42.5 m - Analog Output: Potentiometer, 0...10 V, 4...20 mA - teachable outputs: 0...5 V, 0...10 V, with an additional Open-Collector switching output - Incremental Output: RS422 (TTL), push-pull (HTL) - Digital Output Absolute: CANopen, SSI, Profibus, EtherCAT, Profinet - Linearity up to ±0.02 % of full scale - Protection class up to IP67 - Temperature range -20...+85 °C (optional -40 °C) - High dynamics - High interference immunity factor - Customised versions available

INTRODUCTION WayCon Positionsmesstechnik GmbH is a manufacturer of high quality draw wire position sensors for industrial use. Due to its small overall size, its short assembly time and its possible customisation, the SX sensor technology is a cost-effective and flexible solution for a wide range of industrial applications. The dynamics of the draw wire transducer allows a high motion speed and acceleration of the measuring target. Its rugged design and high quality makes applications in harsh industrial environments possible. Special instruments are available with mounting service of...

11 other ranges on request ELECTRICAL DATA ANALOG OUTPUT Potentiometer 1 kO Output Power supply Recommended cursor current Current consumption max. Power consumption max. Output current Dynamics Resolution Noise Inverse-polarity protection Short-circuit proof Working temperature Temperature coefficient Electromagnetic compatibility (EMC) Circuit 0...5 V, 0...10 V, galvanically isolated, 4 conductors theoretically unlimited, limited by the noise dependent on the quality of the power supply 16 yes --20...+85 °C / optional: -40...+85 °C 0.0079 %/K according to EN 61326-1:2013 V + Signal v...

TECHNICAL DATA DIGITAL OUTPUT INCREMENTAL Measurement range 1) ±0.05 (independent of the measurement range) Improved linearity (optional) ±0.02 (independent of the measurement range, only in combination with resolution 6 pulses/mm, or higher) 0.3 / 3 / 6 / 15 (the resolution can be raised by the factor 4 using quadruple edge detection) Selectable resolution Z-Pulse distance Sensor element connector output M12 or M23 or radial cable output (PVC, standard length 2 m) Protection class maximum 90 % relative, no condensation [°C] Mechanical data extraction force, maximum velocity and maximum...

TECHNICAL DATA DIGITAL OUTPUT ABSOLUTE CANopen (WCAN) Measurement range Sensor element connector output M12, 5 pins, axial (WCAN) or connector output M12, 8 pins, axial (WCANP) Protection class maximum 90 % relative, no condensation see „electrical data“ below Mechanical data Weight extraction force, maximum velocity and maximum acceleration see „Mechanical Data“ [g] 3200 to 5000, depending on the measurement range aluminium, anodised, spring case PA6 ELECTRICAL DATA DIGITAL OUTPUT ABSOLUTE CANopen (WCAN) CAN specification Communication profile Device profile Encoder, absolute linear; CIA...

TECHNICAL DATA DIGITAL OUTPUT ABSOLUTE SSI Measurement range ±0.05 (independent of the measurement range) Resolution scalable (with Software) Standard resolution Maximum resolution Sensor element Multiturn-Absolute-Encoder with optical code disk Power supply Current consumption (no load, at 24 VDC) 10...30 (reverse polarity protection of the power supply) max. 50 Protection class Mechanical data -20...+80 extraction force, maximum velocity and maximum acceleration see „Mechanical Data“ 3200 to 5000, depending on the measurement range aluminium, anodised, spring case PA6 Special cables...

TECHNICAL DRAWING ANALOG OUTPUT AND DIGITAL OUTPUT WCAN * For sensors with measurement ranges of 30 m or greater and radial connector output the encoder length is 120 mm instead of 100 mm. TECHNICAL DRAWING DIGITAL OUTPUT INCREMENTAL Cable / Connector axial, cable radial Connector radial Stecker/ connector radial M12 Stecker/ connector axial M12 Stecker/ connector radial M23 Stecker/ connector axial M23 Kabel/ cable radial TECHNICAL DRAWING DIGITAL OUTPUT ABSOLUTE Profibus, Profinet, EtherCAT

TECHNICAL DRAWING MOUNTING OPTIONS 1. by using the grooves in the sensor housing The included slot nuts can be easily inserted into the grooves of the sensor housing. The slot nuts have a metric M6 thread. 10,6 Each sensor with a measurement range of 20 m or lower is delivered with two slot nuts. Each sensor with a measurement range of 25 m or greater is delivered with four slot nuts. Each sensor with a measurement range of 20 m or lower is delivered with two brackets. Each sensor with a measurement range of 25 m or greater is delivered with four brackets. The angle clamp brackets feature a...

OPTIONS The following table gives an overview of frequently used options, with which the standard sensors can be equipped. Please pay attention that not all options can be combined. Information on possible combinations can be found in the order codes. Option Changed cable or connector orientation (NOT with analog output) Description Rope outlet points upwards: Standard: sideways, opposite to the rope outlet K1: at the top K2: sideways, same side as the rope outlet K3: at the bottom Option K1 Standard for cable / connector Improved linearity Inverted output signal (analog output only)...

Draw wire sensors with the analogue output versions 5VT and 10VT are equipped with teachable, internal electronics, called VT-Electronics. The signals provided by the sensor's potentiometer are digitized by the VT-Electronics. This digital information is first processed by the electronics, then transformed back and given out as an analogue output signal 0 to 5 V or 0 to 10 V. The digitization offers two possibilities of adjustment, by which the sensor can be configured individually using the Squeezer: 1. Teaching of the measurement range. After a successful teaching process, the squeezer...

ORDER CODE ANALOG OUTPUT SX135 Measurement range [m] 10 / 12 / 15 / 20 / 25 / 30 / 35 / 40 / 42.5 Output signal Potentiometer Voltage Voltage Voltage Current Connection Connector output M12, axial, 4 pins Connector output M12, radial, 4 pins Cable output, axial 1) Version Standard Sensor with options Description improved linearity ±0.05 % inverted output signal rope fixation M4 thread rope fixation eyelet protection class IP67 corrosion protection increased corrosion protection increased temperature -40...+85 °C Description cable/connector orientation top cable/connector orientation left...