Catalogs >
WayCon Positionsmesstechnik GmbH >
Draw Wire Mechanics Series SX

Draw Wire Mechanics Series SX
9Pages

Catalog excerpts

Content: Introduction Technical Data Technical Drawing Options Accessories Order Code Series SX draw wire mechanics for encoder assembly Key-Features: - Fast and easy encoder mounting - Measurement ranges from 1 to 42.5 m - Linearity ±0.05 % of full range (with encoder) - Optional high corrosion protection - Temperature range -20...+85 °C (optional -40 °C) - High dynamics - Customised versions available

Open the catalog to page 1

INTRODUCTION WayCon Positionsmesstechnik GmbH is a manufacturer of high quality draw wire position sensors for industrial use. Due to its small overall size, its short assembly time and its possible customisation, the SX sensor technology is a cost-effective and flexible solution for a wide range of industrial applications. The dynamics of the draw wire transducer allows a high motion speed and acceleration of the measuring target. Its rugged design and high quality makes applications in harsh industrial environments possible. Special instruments are available with mounting service of...

Open the catalog to page 2

TECHNICAL DATA SX80 MECHANICS Measurement range Linearity Sheave circumference ±0.05 (with encoder output) Extrection force Fmin Extrection force Fmax Velocity Vmax Acceleration amax 700 to 900, depending on the measurement range clamping flange diameter: 36, shaft diameter: 10, shaft length: 20 Housing Encoder requirements aluminium, anodised, spring case PA6 TECHNICAL DATA SX120 MECHANICS Measurement range Linearity Sheave circumference ±0.05 (with encoder output) Extrection force Fmin Extrection force Fmax Velocity Vmax Acceleration amax 1300 to 1600, depending on the measurement range...

Open the catalog to page 3

TECHNICAL DRAWING SX120 MECHANICS

Open the catalog to page 4

TECHNICAL DRAWING SX135 MECHANICS MEASUREMENT RANGE FROM 10 m Measurement range [m] Position rope outlet at ...

Open the catalog to page 5

TECHNICAL DRAWING MOUNTING OPTIONS SX80 AND SX120 Mounting: standard rope outlet, rope outlet sideways top (S1) Mounting: rope outlet sideways bottom (S2), rope outlet bottom (S3) The sensor is usually installed by using the regular mounting plate Sensors with option rope outlet S2 and S3 have a modified base plate: (see technical drawing above). By disassembling the mounting plate, there are 2 x M4 threads in SX80 SX120 30 the sensor housing for alternative installation. 13,75 TECHNICAL DRAWING MOUNTING OPTIONS SX135 1. by using the grooves in the sensor housing The included slot nuts can...

Open the catalog to page 6

OPTIONS The following table gives an overview of frequently used options, with which the standard sensors can be equipped. Please pay attention that not all options can be combined. Information on possible combinations can be found in the order codes. Option Changed rope outlet Description Standard: rope outlet at the top S1: rope outlet sideways at the top S2: rope outlet sideways at the bottom S3: rope outlet on the bottom Synthetic wire rope (instead of stainless steel wire rope) Synthetic wire rope, made out of abrasion resistant and enhanced Coramid. Rope fixation by M4 thread...

Open the catalog to page 7

Rope extension - SV For bridging a greater distance between the measuring target and the sensor a rope extension can be applied. The rope clip must not be guided over the deflection pulley. Please specify the length needed in your order (XXXX). The minimum length is 150 mm: SV1-XXXX: rope extension (150...4995 mm) SV2-XXXX: rope extension (5000...19995 mm) SV3-XXXX: rope extension (20000...40000 mm) Magnetic clamp - MGG1 Use the magnetic clamp to quickly attach the rope to metallic objects without any assembly time. A rubber coating provides gentle contact (e. g. on varnished surfaces) and...

Open the catalog to page 8

ORDER CODE SX135 MECHANICS MEASUREMENT RANGE FROM 10 mSX135 — F58K — Option M4 RI CP T40 Description rope fixation M4 thread rope fixation eyelet corrosion protection increased temperature -40...+85 °C UR2 deflection pulley SV1-XXXX rope extension (150 mm up to 4995 mm) MGG1 magnetic clamp SV2-XXXX rope extension (5000 mm up to 19995 mm) Subject to change without prior notice. WayCon Positionsmesstechnik GmbH email: info@waycon.de internet: www.waycon.biz Wauton Positionsmesstechnik

Open the catalog to page 9

Draw Wire Mechanics Series SX 9Pages

Catalog excerpts

All WayCon Positionsmesstechnik GmbH catalogs and technical brochures

Draw Wire Mechanics Series SX
9Pages