catalogue search
P. 01
P. 02
P. 03
P. 04
P. 05
P. 06
P. 07
P. 08
P. 09
P. 10
P. 11
P. 12
P. 13
P. 14
P. 15
P. 16
P. 17
P. 18
P. 19
P. 20
P. 21
P. 22
P. 23
P. 24
P. 25
P. 26
P. 27
P. 28
P. 29
P. 30
P. 31
P. 32
P. 33
P. 34
P. 35
P. 36
P. 37
P. 38
P. 39
P. 40
P. 41
P. 42
P. 43
P. 44
P. 45
P. 46
P. 47
P. 48
P. 49
P. 50
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You may also be interested in
Thermocouple, Heater, Band heater, Cable, Power regulator
Text version of the page
| Auto-Tuning PID Controllers | ||||||||||||
| • Electrical life 100,000 cycles at rated current • For resistive loads only, must use RC suppression for inductive loads Process • Range selectable: 0-20mA, 4-20mA, 0-5V^(dc), 1-5V=(dc), 0-10Vī(dc) • Reverse or direct acting • 0 to 10V==(dc) voltage output into 10000 minimum load resistance • 0 to 20mA current output into 8000 maximum load resistance • Resolution: V==(dc) ranges = 2.5mV nominal mA ranges = 5uA nominal • Calibration accuracy: V==(dc) ranges = ±15mV mA ranges = ±30uA • Temperature stability 100ppm/°C Retransmit • Range selectable: 0-20mA, 4-20mA, 0-5V^(dc), 1-5V=(dc), 0-10Vī(dc) • 0 to 10V==(dc) voltage output into a 1,0000 minimum load resistance • 0 to 20mA current output into an 8000 maximum load resistance • Resolution: V==(dc) ranges = 2.5mV nominal mA ranges = 5uA nominal • Calibration accuracy: V==(dc) ranges = ±15mV mA ranges = ±30uA • Temperature stability 100ppm/°C Communications • EIA/TIA-485, EIA/TIA-232 • Opto-isolated • Modbus™ RTU protocol • 1200, 2400, 4800, 9600, 19200 baud rates • 32 maximum units can be connected (With additional 485 repeater hardware, up to 247 units may be connected) | ||||||||||||
| SERIES 96 Specifications Cont. • Input sampling rates: Single Input 10Hz (100ms), dual input 5Hz (200ms) digital filter adjustable • Display update: 2Hz (500ms), time filter adjustable • Output update: burst, 0.1 to 999.9 seconds • Input/Output/Communication isolation • Displayed in °C, °F, or process units Operator Interface • Dual four-digit LED displays: upper 10.2 mm (0.4 in.), lower 6.2 mm (0.244 in.) • Advance, Up Arrow, Down Arrow, Infinity tactile keys Standard Conditions For Specifications • Ambient temperature 25°C (77°F) ±3°C, rated line voltage, 50 to 60Hz, 0 to 90 percent RH non-condensing, 15 minute warm-up Universal Input 1 Thermocouple • Type J, K, T, N, C (W5), E, Pt 2, D (W3), B, R, S thermocouple • >20M0 input impedance • Maximum 200 source resistance • 30uA open detection bias RTD • 2- or 3-wire platinum, 1000 • JIS and DIN-curves • Whole or tenth degree indication • 150uA nominal RTD excitation current Process • Range selectable: 0-10V-(dc), 0-5V-(dc), 1-5V-(dc), 0-20mA, 4-20mA • Voltage input impedance 20k0 • Current input impedance 1000 • Minimum current source resistance 1M0 | • Input resolution 50,000 bits (approx.) at full scale • mV input impedance 20MO Input 2 Event Input • Contact or voltage • 20KO input impedance • Voltage input: event high state 3 to 36V^(dc), event low state 0 to 2V^(dc) • Resistance/contact input: event high state >23kO, event low state 0 to 2kO Remote Set Point Input: mA or Vī(dc) Range Selectable • Voltage input impedance 20kO • Current input impedance 1000 Output Types Open Collector/Switched DC • Open collector configuration: Maximum voltage 42V^(dc) Maximum current 200mA Maximum on resistance 1.10 Maximum off state leakage current 100uA • Switched dc configuration: Switched dc supply voltage 22 to 28V^(dc) dc supply current limited to 30mA Solid State Relay • Optically isolated • Zero cross switched • Without contact suppression • Minimum load current 0.5mA rms • Maximum current 0.5A rms at 20 to 280V~(ac) • Maximum off state leakage current 10uA rms • For resistive loads only, must use RC suppression for inductive loads Electromechanical Relay • Form C contact configuration • Minimum load current 10mA @ 5V^(dc) • Rated resistive and inductive loads: 2A @ 250V~(ac) or 30V^(dc) maximum | |||||||||||
| 36 | ||||||||||||