| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | Motor Driven | | |
| | | www.velmex.com | | |
| | | |
| | | |
| | | | | |
| | | |
| | | The motor to lead screw connection is a precision honed steel coupling that rigidly clamps to the motor shaft without the need for key ways or set screw flats. Size 23 motors use a 0.375" to 0.250" coupling bushing; size 34 motors use a 0.375" coupling and an additional plate. Motor-Driven BiSlides are available in standard travels to 80"/203.2 cm. Please refer to the chart on page 2.39. | |
| | | All BISIIdes are designed to accommodate NEMA size 23 and size 34 motors without modifications. Many other types of motors can also be used, most of them requiring no modifications to the BiSlide. All BiSIides can be purchased with, or without motors. Related motor drives, controls, and software are also available. | | |
| | | |
| | | |
| | | BiSlide Lead Screw Torque/Load* | | |
| | | |
| | | 200 180 160 140 120 100 80 60 40 20 0 | | |
| | | E04 | | |
| | | |
| | | CD ■o O o CD CD _l 82 u (O T3 CO CD _l | | |
| | | "T N CD 3 CT | | |
| | | M01 E01 M02 | | |
| | | |
| | | |
| | | |
| | | |
| | | 100 Lifting (thrust) ..... Sliding (normal) | | |
| | | 10 20 30 100 200 300 | | |
| | | |
| | | |
| | | Load (lbs) Add 35 oz-in for Parallel Coupled, 1.5x torque for dynamic safety margin, 2x torque needed for startup | | |
| | | |
| | | Motor Mounting | | |
| | | |
| | | 3.00" L | | |
| | | | | | | | | | Motor Size | A | | | | Nema 23 Two Stack (PK 264) | 2.13" | | | | Nema 23 Three Stack (PK 268) | 2.99" | | | | | | | | Motor Size | A | | | | Nema 34 One Stack (M091-FD-454) | 2.90" | | | | Nema 34 Two Stack (M092-FD-447) | 4.15" | | | | | | | | | |
| | | |
| | | |
| | | ■A- | | |
| | | | | | |
| | 1.58" Choose the lead screw that fits your application. | |
| | | An Important Note About Lead Screws: The E01, M01 and M02 are self-locking designs that under normal conditions will not creep or backdrive (external forces on carriage do not cause lead screw to rotate). However, with the motor power off, the E04 can backdrive when used vertically or when the thrust load exceeds 2 lbs. | | |
| | | |
| | | | | | | | | | | Lead Screw | Advance/Turn | | | | | E01 | 0.100" | 0.00025" | | | | E04 | 0.400" | 0.001" | | | | M01 | 1 mm | 0.0025 mm | | | | M02 | 2 mm | 0.005 mm | | | | | | | | | | |
| | | |
| | | |
| | | 2.40 Motorized BiSlide | | 1-800-642-6446 | | |
| | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |