Catalogues - variable-frequency-drive-inverter-starvert-ih

Catalogue Variable Frequency Drive / Inverter - Starvert iH

www.vmc.es

Page

/ 20

Where to buy
this product ?

Request
a Quote

/ 20

See other catalogues for Vector Motor Ibérica

Text version of the page

Starvert iH

2. Function Group


Code [FUN]	Description of Function Group	Keypad Display	Setting Range	Units	Factory Default	Adjustable during run
45D	Stall Prevention Mode	Stall mode0	None, Acc, Steady, Acc + Steady, Dec, Acc + Dec, Dec + Steady, Acc + Dec+Steady		None	Yes
46D	Stall Prevention Level	Stall levelO	CT: 30 to 150 [%] VT: 30 to 150 [%]	1 1	150 [%] 110 [%]	Yes Yes
47D	Overload Warning Level	OL levelO	CT: 30 to 150 [%] VT: 30 to 110 [%]	1 1	150 [%] 110 [%]	Yes Yes
48	Overload Warning Hold Time	OL time0	1 to 30 [sec]	1	10 [sec]	Yes
49D	Over Current Trip Limit Level	OC lim levelO	CT: 30 to 200 [sec] VT: 30 to 150 [sec]	1 1	160 [%] 110 [%]	Yes Yes
50D	Over Current Limit Time	OC lim. Time0	0 to 60 [sec]	0.1	60 [sec]	Yes
51D	Electronic Thermal Selection	ETH selectO	No, Yes		No	Yes
52D	Electronic Thermal Level	ETH levelO	30 to 150 [%]	1	150 [%]	Yes
53D	Electronic Thermal Characteristic (Motor Type) Selection	Motor type O	General, Special		General	Yes
54D	Number of Motor Poles	Pole number O	2 to 12	1	4	Yes
55D	IPF (Instant Power Failure) Restart Selection	IPF select O	No, Yes		No	Yes
56	Speed Search Acceleration Time	SS acc. time O	0.1 to 600 [sec]	0.1	5 [sec]	Yes
57	Speed Search Deceleration Time	SS dec. TimeO	0.1 to 600 [sec]	0.1	10 [sec]	Yes
58	Speed Search Gain	SS gainO	0 to 200 [%]	1	100 [%]	Yes
59	Restart after Fault Reset Selection	RST-restartO	No, Yes		No	Yes
60	Power-On Start Selection	Power on st O	No,Yes		No	Yes
61	Carrier Frequency	Carrier Freq O	2 to 10 [Hz]	1	6 [Hz]	No
62	PI Control Selection	PI-controlO	No,Yes		No	No
63	PI Proportional Gain	P-gainO	1 to 30000	1	10	Yes
64	PI Integral Gain	I-gainO	1 to 30000	1	50	Yes
65	PI Feedback Selection	PI-fb select O	I, V1, V2		I	No
66	PI Feedback Filter Gain	PI-fb filt.GO	1 to 100 [%]	1	25 [%]	Yes
67	PI Feedback Gain	PI-fb gain O	50 to 250 [%]	0.1	100.0 [%]	Yes
68 69 70	PI Feedback Bias PI Feedback Direction PI I Gain Scale	PI-fb bias Pl-fb dir O I__term scale O	0 to 200 [%] Direct,Invert 1 to 100 [%]	0.1 1	100.0 [%] Direct 100 [%]	Yes No Yes
71	PI Controller Error Direction	PI error dir O	Direct,Invert		Direct	No
72 «121	PI Control Bypass	Regul bypassO	No, Yes		No	No
94 ¹	CT/VT Selection	CT/VT	Constant Trq,Variable Trq		Constant Trq	No
95	Read Parameters into Keypad from Drive	Para. Read O Q	No, Yes		No	No
96	Write Parameters to Drive from Keypad	Para. WriteO	No,Yes		No	No
97	Initialize Parameters to Factory Default Settings	Para. InitO Q	No,Yes		No	No
98	Parameter Write Protection	Para. Lock	0 to 255	1	0	Yes

*9)

Default value depends on the drive capacity,

-10)

FUN 41 is set at its drive capacity before shipping outside. However, drive loses its capacity information after parameter initialization in FUN 97, If the parameters are initialized, be sure to re-set the drive capacity to the right capacity,

Carrier Frequency according to the drive Capacity (The Carrier Frequency is set to 3kHz for VT Rating)


type	SettingRange	Factory Default	type	SettingRange	Factory Default
SV030ÌH-2	2 to 10	6kHz	SV075ÌH-4	2 to 7	6kHz
SV037ÌH-2	2 to 10	6kHz	SV090ÌH-4	2 to 6	6kHz
SV045ÌH-2	2 to 8	6kHz	SV110ÌH-4	2 to 6	6kHz
SV055ÌH-2	2 to 8	6kHz	SV132ÌH-4	2 to 5	5kHz
SV030ÌH-4	2 to 10	6kHz	SV160ÌH-4	2 to 4	4kHz
SV037ÌH-4	2 to 10	6kHz	SV220iH-4	2 to 4	4kHz
SV045ÌH-4	2 to 8	6kHz	SV315ÌH-4	2 to 4	4kHz
SV055ÌH-4	2 to 8	6kHz	SV375ÌH-4	2 to 4	4kHz

*12)

VT is available only for 440V class industrial inverter.