| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | SPECIALTY FLUIDS, CLEANERS & ADDITIVES | | |
| | | COOL | | |
| | | |
| | | |
| | | DFSCRIPTION | | APPIICATION | | |
| | | PRODUCT | | | OTHER | | |
| | | |
| | | |
| | | • Water conditioner which prevents foam problems. • Can be added to soft water (less than 100 ppm hardness) in either individual machines or central system reservoirs. | | |
| | | PACKAGING • 5 gal. (19 liter) pails • 55 gal. (205 liter) drums LITERATURE Flyer PC VAL-24 | | |
| | | 1:5000. • Not recommended for use with ValCOOL synthetic fluids. | | |
| | | |
| | | |
| | | |
| | | • Broad spectrum bactericide and fungicide commonly used in cutting fluid mixes to eliminate existing mold and bacteria. | | • Add directly to the clean side of the cutting fluid mix at a ratio of 10 ounces to every 50 gallons of cutting fluid mix. • Caution: Consult a Valenite representative before using. | | |
| | | PACKAGING 10 lb. (4.5 Kg) container or 1 gal. (3.8 liter) 45 lb. (20.25 Kg) pail or 5 gal. (19 liter) 500 lb. (225 Kg) drum or 55 gal. (205 liter) | | |
| | | |
| | | |
| | | |
| | | • I ndustrial microbiostat, which prevents the growth of fungi and bacteria in metalworking fluids. | | Add directly to the clean side of the cutting fluid mix. Dilute 13 ounces to 50 gallons. Caution: Consult a Valenite representative before using. | | |
| | | PACKAGING •1 gal. (3.8 liter) container • Case of (4) 1 gal. (3.8 liter) containers. | | |
| | | |
| | | |
| | | |
| | | • Non-silicon defoamer used to temporarily control excessive foam, machines. | | • Add directly to the clean side of the cutting fluid mix at a ratio of 1 ounce per 200 mixed gallons of cutting fluid. • Caution: Consult a Valenite representative before using. | | |
| | | PACKAGING • 5 gal. (19 liter) pails • 55 gal. (205 liter) drums LITERATURE Flyer PC VAL-4 | | |
| | | |
| | | |
| | | |
| | | • pH adjuster used to raise the pH in ValCOOL cutting fluid mixes. | | • Add directly to the clean side of the cutting fluid mix at a ratio of 1:1000 to 1:2000. • Caution: Consult a Valenite representative before using. | | |
| | | PACKAGING • 5 gal. (19 liter) pails • 55 gal. (205 liter) drums LITERATURE Flyer PC VAL-5 | | |
| | | |
| | | |
| | | |
| | | • Rust inhibitor additive which, when added to ValCOOL cutting fluids, replenishes and improves the rust inhibitors in the cutting fluid mix. | | Add directly to the clean side of the cutting fluid mix at a ratio of 1:500 to 1:1000. Caution: Consult a Valenite representative before using. May cause staining of non-ferrous materials. | | |
| | | PACKAGING • 5 gal. (19 liter) pails • 55 gal. (205 liter) drums LITERATURE Flyer PC VAL-17 | | |
| | | |
| | | |
| | | |
| | | Material safety data sheets available at www.valenite.com Not recommended for use with magnesium | | |
| | | |
| | | Customer Service (USA) : 1.800.544.3336 (Canada) : 1.800.265.9504 Technical Support : 1.800.488.9073 | | |
| | | |
| | | Valenite' | | |
| | | 12 | | |
| | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |