| | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | insulated conductors u 10 | | |
| | | |
| | | General VAHLE insulated conductors U 10 are designed in accordance with today's international safety requirements. They fully meet VDE 0100 and are finger safe to VDE 0470, part 1, protection code IP 21. | | |
| | | Joints Snap-in joint splices provide mechanical end electrical continuity. They include insulated protection covers. Expansion joint sections are only required in case of expansion joints in the monorail track. | | |
| | | |
| | | |
| | | The adjacent picture demonstrates that the VDE test finger cannot reach life conductors -finger safety is guaranteed. | | |
| | | Feed terminals Joint assembly and mid-rail assembly feeds are available. Furthermore transfer guides and isolating assemblies allow for spado connectors. | | |
| | | |
| | | The shroud which envelopes the various conductors is an excellent insulator. Therefore our unipole insulated conductors guarantee utmost safety in operation. | | |
| | | |
| | | |
| | | Transfer guides Transfer guides serve as an end protection of system runs and accomplish smooth collector transfer in case of switches, drop sections etc. They can be supplied with or without feed clip. Isolating assemblies Conductor isolating assemblies are available for sectionalizing control circuits, maintenance bays etc. They can be supplied with or without feed clip. | | |
| | | Any tiumber of conductors can be installed side by side at minimum space requirement. | | |
| | | |
| | | Standard rail sections are 6 m long, shorter sections are available. | | |
| | | |
| | | The ground conductor Is identified by international colour coding. | | |
| | | |
| | | |
| | | For obvious safety reasons phase and ground collectors are not interchangeable. Approved and listed by: UL. Consult factory label service. Hangers Bolted, snap-in and quarter turn type hangers are available. Standard support distance for U 10 is 600 mm, in curves 300 mm. | | |
| | | Curves Insulated conductors U 10 can be used for horizontal or vertical curves. A special curve tool for individual field preparation is available. | | |
| | | |
| | | Collectors The current collectors are made of reinforced polyamide and stainless steel parts. These spring loaded units provide positive contact with the conductor bars and have double pick-up brushes. | | |
| | | |
| | | |
| | | Engineering data of shroud | | |
| | | |
| | | | | | | | | | | | standard shroud color green | high temp, shroud color gray | | | | Electrical properties: Di-electric strength DIN 53481 | 30-40 kV/mm | 45 kV/mm | | | | Specific resistance DIN 53482 | 5 x 101f Ohm x cm | 5 x 10" Ohm x cm | | | | Surface resistance DIN 53482 | 10;? Ohm | 10''Ohm | | | | Leakage resistance IEC 112A/DE 0303 | CTI 600- 1.1 | CTI 600- 1.1 | | | | Mechanical properties: Flexible strength | 75 N/mm'± 10 % | 95 N/mm' ± 10 % | | | | Tensile strength | 50 N/mm'± 10 % | 50 N/mnrf ± 10 % | | | | Temperature resistance: | -30° CUR to +55° C | -30° Cup to +85° C | | | | Flame test proof per DIN 4102 - part 1 | class B1 - no flaming particles, self-extinguishing | | | | Resistance to chemicals:* | gasoline hydrochloric acid, concentr. mineral oil caustic soda solution 25% and grease 50%, sulphuric acid to 50% | | | | | | | | | | |
| | | |
| | | 3 | | |
| | | * Consult factory when synthetic oil and grease involved. | | |
| | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | |
