| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | ] !ÜUui!i | | |
| | | |
| | | TECHNICAL SPECIFICATIONS | | |
| | | |
| | | Work area - Number of work zones X-axis, column travel - per work zone mm Y-axis, cross travel mm Z-as, height travel mm Distance spindle nose to table top mm | | |
| | | 1.000 or 2.000 800 500 200 - 700 | | |
| | | |
| | | |
| | | Table sizes, per table T-slots Distance T-slots Admissible table load per table | | |
| | | mm 850 x 1.000 mm 18H8(1x), 18H12 mm 125 kg 2.000 | | |
| | | |
| | | | | |
| | | 680 x 680 M12 32 3.000 750 | | |
| | | |
| | | Location hole pattern (40-80 mm) Maximum speed of rotation min"1 Maximum drive torque Nm Admissible table load kg | | |
| | | |
| | | |
| | | Milling & drilling spindle - Direct drive, AC (S6-40%) kW 36 (S1-100%) kW 26 Spindle speed - standard, direct drive rpm 12.000 - optional, direct drive rpm 16.000 Max. available torque - direct drive (S6-40%) Nm 180 -direct drive (S1-100%) Nm 130 Main spindle bearing diameter mm 70 | | |
| | | |
| | | Motor spindle - Spindle A: 25.000 rpm, 70 kW (S6 - 40%), 90 Nm (S6 - 40%) Spindle B: 25.000 rpm, 100 kW (S6 - 25%), 90 Nm (S6 - 40%) | | |
| | | |
| | | Tool system - Stationary chain type tool magazine Taper size 1 - DIN 69871/72 form A or - DIN 69893 form A Number of pockets Maximum tool size - with loaded adjacent pockets - with empty adjacent pockets - depending on shape Maximum tool length Maximum tool weight Tool change time | | |
| | | | | | | | | | # | ISO 40 | | | | # | HSK63 | | | | - | 63/163 | | | | mm 0 | 95 | | | | mm 0 | 120 | | | | mm | 120x 200 | | | | mm | 350 | | | | kg | 10 | | | | sec. | 4,5 | | | | | | | | | |
| | | POWER/TORQUE CHARTS | | |
| | | |
| | | = Direct drive, 12.000 min1 = Direct drive, 16.000 min1 | | = Direct drive, 12.000 min1 = Direct drive, 16.000 min1 | | |
| | | |
| | | |
| | | Axis drive and feed system - Digital AC-Servo drives Rapid traverse X-, Y-and Z-axis mm/min Feed rate X-, Y- and Z-axis mm/min Acceleration X-, Y-and Z-axis m/sec2 Feed thrust X- and Y-axis N Drilling thrust Z-axis N | | |
| | | |
| | | 60.000 5 - 60.000 | | |
| | | |
| | | 10.000 16.000 | | |
| | | |
| | | |
| | | Capacity in C45 Drilling Tapping Milling Power supply | | |
| | | 50 M 30 400 | | |
| | | cm3/min | | |
| | | |
| | | |
| | | |
| | | Power consumption, approximately Electrical equipment for | | KVA 70 400V/3ph/50Hz | | |
| | | |
| | | We reserve the right to change technical specifications without prior notice. | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |