Catalog excerpts
STANDARD TYPE WEIGHING INDICATOR New Standard for Weighing Indicator!! ved basic-performance supported Significantly improved basic-performance. SD memory card is supported. SD card slot You can write and read setting parameters from SD cards, while recording weighing results & data when abnormalities occur. Calibration value & Error logs are automatically recorded You can identify the indications of faulty load cells and replacement timing.Date & time of errors occurred can be displayed, as well as the record of how the errors are made (through key control, communication, I/O, etc). Data recording of weighing results Monitor management of raw material, equipment operation rate and so on. Long-term trend can be observed as well. By placing the rubber seal when mounting on the panel, the front panel can be protected from moisture and dust damage. High sampling rate & resolution High-Speed A/D conversion and powerful digital processing capability of 1200 times/sec.High display resolution of 1/100000 (max).Measurement can be performed quickly and precisely due to high speed A/D conversion. Load cell signal level display (-2.51mV/V to 5.1mV/V) The output signal level of load cell can be displayed in mV/V for monitor purpose.Malfunction indicator or faulty sensor can be differentiated easily. Restore setting parameters with just one touch ・ You can copy setting parameters to another replaced FC1000. ・ Multiple FC1000s can use the exact same settings. ・ You can restore the initial setting when you first install FC1000. (It will be saved as initial value separately from the setting parameters). Total weight control functiont 高速応答 The batch weighing with a low capacity scale enables the fast and accurate measurement of larger total weight. 【Coarse feeding】 【Fine feeding】 Depth of 99mm Miniaturization of control panel & panel space saving. High performance filter & Auto filter adjustment With combination of low pass filter (0.1 to 300Hz) which corresponds to various vibration and moving average filter (OFF, 2 to 512) that is effective for periodic vibration, automatic searching for optimal value with accuracy and stability can be achieved. (You can manually adjust settings too) By simply pressing the auto adjustment key…. Load cell The batch weight is adjusted automatically based on the target total weight, and the feeding is controlled in three steps (SP1/SP2/SP3) for more accurate weight measurement. Feeding hopper At first, coarse feeding is performed with lower accuracy. But, when the total weight reaches to the total weight set point, the weighing mode automatically switches to fine feeding with the higher accuracy. higher accuracy. Minus compensation High-pressure liquid filling & powder feeding can be done. All three feeding valves are opened fully for faster weighing. Control the feeding valves Load cell Load cell
Open the catalog to page 1Bright white LCD display with the useful 20 digits sub display. Equivalent input calibration Theoretical calibration can be performed easily by registering the capacity and rated output of load cells. Multipoint calibration (linearization) 24 bit A/D convertor enables 6 digit display. Memory for 32 weight settings 32 different weight settings can be saved in the memory and selected through I/O or interface. Batch weighing can be performed easily. Three additional points can be defined in the middle between zero and span for better linearity. Even though the scale has poor linearity, it can...
Open the catalog to page 2All UNIPULSE Corporation catalogs and technical brochures
-
F650-CK
1 Pages
-
F600AT
1 Pages
-
F850
1 Pages
-
F805AT-MD
1 Pages
-
F805AT-BC
1 Pages
-
F805AT-CF
1 Pages
-
F805AT-FB
1 Pages
-
F805AT-CK
1 Pages
-
FC400-EIP
2 Pages
-
RSCC
1 Pages
-
HLCB1
1 Pages
-
SB14
1 Pages
-
Z6FC3/Z6FD1
1 Pages
-
PW4M
1 Pages
-
PW6C
1 Pages
-
PW10A
1 Pages
-
PW15A
1 Pages
-
UPP-100N
1 Pages
-
UPP-100NX3
1 Pages
-
UTM II Series
40 Pages
-
USM
1 Pages
-
SCB:Rev.1.02
2 Pages
-
UNLS
1 Pages
-
UNBF
1 Pages
-
UNCLB
1 Pages
-
UNCSR
1 Pages
-
UNGS
1 Pages
-
UNLRS
1 Pages
-
UNTCH
1 Pages
-
UNCDW
1 Pages
-
UNMR
1 Pages
-
USB58
1 Pages
-
FC400 Force
1 Pages
-
FS2000
2 Pages
-
F381A
2 Pages
-
F372A
2 Pages
-
F325
1 Pages
-
F331
1 Pages
-
F350
1 Pages
-
F490A
1 Pages
-
F130
1 Pages
-
ULE-50
1 Pages
-
GM400
2 Pages
-
F805AT
1 Pages
-
F701-S
1 Pages
-
F701+
2 Pages
-
F159
1 Pages
-
B412
1 Pages
-
513B
1 Pages
-
TM301
1 Pages
-
TM201
1 Pages
-
TM500
1 Pages