F381A
2Pages

DIGITAL INDICATOR WITH GRAPHIC DISPLAY/TOUCH PANEL (SD CARD SLOT OPTION AVAILABLE) Comparison & Hold Function by Waveform Display These functions are used to judge the acceptability of measurement waveforms. Depending on type of applications, Waveform Comparison Function and Multi Hold Function can be jointly utilized for judgment. Waveform Comparison Function Hi and Lo limit comparison of overall measurement Hi Limit Setting waveform can be performed. Type of hold can be selected at segmented measuring area. Saves Measurement Data in SD Card Measurement data and set values can be logged (recorded) in the SD Card where it can be retained as a 100% recorded quality data or be used when setting up equipments or when performing cause analysis or improvement of problems. The data can be easily converted to CSV format and is therefore easily edited in Microsoft Excel or its like. CE marking certification RoHS-compliant product • 4000 times/sec high-speed processing Analog monitor output Voltage output is proportionate to the input signal making the recording on recorder convenient. Approx. 2V per 1 mV/V strain gauge input • Variety of interfaces RS-232C / DeviceNet / CC-Link / Ethernet • 3.5-inch color LCD module & touch panel Operation can be effortlessly performed by a direct touch on the touch panel. Excellent operability F381A is right-down demanding on straightforwardness and is therefore made able to automatically mask non-required setting items and also to display setting in the required sequence when that particular set item has specific setting sequence. • I/O Input: Plus common / Minus common shared I/O Output: Sink type / Source type selectable. It can be connected to various types of external equipments such as PLCs. Multi hold function After the measuring range is segmented, judgment is carried out while the type of hold (sample, peak, bottom, P-P, Average, max, min, inflection point, End Displacement) is interchanged as set. The multi hold function can specify the Hi/Lo limit value and type of hold at each of the segmented range. Multipoint judgment is possible because the multi hold function is capable of using the peak hold to detect the inhibit timer immediately after the press-fit is started and then uses the inflection point hold to judge the load just before the ramming is commenced. Displacement input as a standard equipment It performs 2-dimensional waveform comparison & multi hold through its dual input from the displacement sensor and strain gauge sensor. On X-axis, voltage or pulse input can be connected while on Y-axis, strain gauge sensor can be connected. This is highly effective for applications which are difficult to control only by time factor such as the control for pressing time of press machines and for the imposing Waveform comparison function This function compares the actual measurement waveform against the setup High/Low limit waveforms and will give out an NG judgment when any of the point exceeded the preset High/Low limit waveforms. As it compares the overall measurement waveform, accurate judgment can be made even applications that are unable to narrow down its ▲Setup Waveform Creation Screen judgment points. The High/Low limit waveforms can be easily created on the actual measurement waveform or on the setup waveform creation screen. time on works with individual differences. *When nothing is connected with X-axis, Waveform Comparison & Multi Hold by the time series can be done. *The voltage input is an option. Judgment results display The comparison results of Waveform Comparison Function and Multi Hold Function can be verified on the display. [Result(List)](An individual display) and [Result (Single)] (a list display) to selection is possible. (Latest 40 data) UniPULiE https ://www. unipulse, tokyo/en/

SENSOR INPUT DTC1 : Special case Unit: mm Structure of product code F381A □ □ □ □© (D (D ® (D ©Standard unit ©Displacement sensor input @1/0 output Digital contact sensor ULE-50 ©Interface A digital contact sensor designed for FS2000 and F381A-LDI. You can perform OK/NOK judgment with a Force vs Displacement curve. ©SD card slot Sign l One optional interface can be added in addition the standard interface. External dimension (Front View) (Side View) (Rear View) Panel cut dimension Panel thickness 1.6 to 3.2 mm UfllPULiE https ://www. unipulse,