Tsubaki Emerson MDEU Series Cam Clutch - Tsubakimoto Chain - #1

Text version of the page

TSUBAKI EMERSON N·m N(*) H7 A B C D E F G H I kg 5 A F C F H G H B E D I 6 7 4 3 2 1 MDEU15 70 600 100 610 15 5×2.3 39 55 37 25 42 1.0 30 3.5 0.5 5×3.0 0.52 MDEU20 150 500 100 910 20 6×2.8 42 68 40 32 52 1.0 33 3.5 0.5 6×3.5 0.88 MDEU25 230 450 100 1,060 25 8×3.3 42 80 40 40 65 1.0 33 3.5 0.5 8×4.0 1.1 MDEU30 390 400 100 1,400 30 8×3.3 50 90 48 45 72 1.0 36 6.0 1.0 8×4.0 1.7 MDEU35 460 350 100 1,500 35 10×3.3 50 100 48 50 80 1.0 36 6.0 1.0 10×5.0 2.1 MDEU40 530 350 100 1,580 40 12×3.3 50 110 48 55 78 1.0 36 6.0 1.0 12×5.0 2.7 MDEU45 690 300 100 1,770 45 14×3.8 50 120 48 65 88 1.0 36 6.0 1.0 14×5.5 3.2 MDEU50 870 300 100 1,880 50 14×3.8 50 130 48 70 95 1.0 36 6.0 1.0 14×5.5 3.8 MDEU55 1,100 250 100 2,850 55 16×4.3 60 140 58 80 105 1.0 46 6.0 1.0 16×6.0 5.3 MDEU60 1,500 250 100 3,060 60 18×4.4 60 150 58 90 115 1.0 46 6.0 1.0 18×7.0 6.1 MDEU70 1,900 200 100 3,470 70 20×4.9 60 170 58 100 125 1.0 46 6.0 1.0 20×7.5 7.9 MDEU80 2,300 200 100 3,600 80 22×5.4 60 190 58 110 140 1.0 46 6.0 1.0 22×9.0 9.7 Economical package solutions No bearings nor flanges required Easy installation New! CAM CLUTCHES MDEU SERIES 1 Inner race 2 Outer race 3 Cam, Roller 4 Spring 5 Plate 6 Spirolox (hole) 7 Spirolox (shaft) Torque capacity Max. overrunning speed Inner race Max. indexing Max. radial load when overrunning Bore size Keyway inner race Keyway outer race Weight Model r/min cycle/min For more information please contact: TSUBAKIMOTO EUROPE B.V. - Belder 1 - NL 4704 RK Roosendaal - The Netherlands Tel. +31 (0)165 59 48 00 - Fax +31 (0)165 54 94 50 - Email info@tsubaki.nl - Internet http://tsubaki.nl - installation and usage - 1. The tolerance of the sprocket, gearor pulley bore and outer race shall be H7 or H8. The recommendable tolerance of shaft is h6 or h7. 2. Usage of parallel keyways between outer race and sprocket, gear or pulley as well as clutch and shaft, is compulsory. 3. When installing the clutch on the shaft, apply pressure only on the inner race. 4. If thrust loads are encountered, other devices which release loads should be applied. 5. When installing a pulley where the radial load is bigger than the max. given load of the clutch, we recommend the use of lateral bearings. See installation figure 2 and refer to column N (*). 6. In arduous environments it is recommended to use MDEU-2GD Series, which have dust seals, in order to prevent contamination. The maximum overrunning speed of 2GD Series is 80% of the standard MDEU Series. Installation 1 General mounting. Installation 2 Belt drive overrunning applications. See item 5: installation and usage. CCMDEU002023 E 2005.03 TEU Printed in the Netherlands B 2,000