catalogue search
P. 151
P. 152
P. 153
P. 154
P. 155
P. 156
P. 157
P. 158
P. 159
P. 160
P. 161
P. 162
P. 163
P. 164
P. 165
P. 166
P. 167
P. 168
P. 169
P. 170
P. 171
P. 172
P. 173
P. 174
P. 175
P. 176
P. 177
P. 178
P. 179
P. 180
P. 181
P. 182
P. 183
P. 184
P. 185
P. 186
P. 187
P. 188
P. 189
P. 190
P. 191
P. 192
P. 193
P. 194
P. 195
P. 196
P. 197
P. 198
P. 199
P. 200
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
You may also be interested in
Seal, Wear ring, Hydraulic seal, Fitting, O-ring seal
Text version of the page
| V-Ring | |||||||||||||||||||||||||||||
| Fitting the clamping band RM Trim the adjustable clamping band to the right length by using a pair of shears. Rivet the adjustable length and the end attachment together by using a standard pop riveter and the three pop rivets. | Clamping band for V-Ring type A and AX The clamping band A/AX is meant to be used with V-rings type A and AX on shaft diameters from 200 mm and larger. The clamping band keeps the V-ring in position both axially and radially and can be re-used several times. The clamping band is supplied in 5 m lengths. Screw joints to connect the clamping band as well as the buckle are ordered on separate article number. The band is made of stainless steel AISI 301, the screw joint is made of AISI 304 with galvanized screw. | ||||||||||||||||||||||||||||
| Locate the V-Ring in correct position relative to counterface, i.e. the predetermined B-pdimension. | the | ||||||||||||||||||||||||||||
| Smear the V-Ring with a thin film of grease in the groove designed for the clamping band. Using the attachments supplied with the band sections, join them together and position the complete band in the body groove with the screw heads facing the direction of shaft rotation. Turn the attachment screws a few turns one by one until the band is tight. Check that the entire band fits snugly in the body groove. | |||||||||||||||||||||||||||||
| To order the right size and for the | correct installation. | ||||||||||||||||||||||||||||
| please ask for the "TECH INFO". TSS part numbers for clamping band A: | |||||||||||||||||||||||||||||
| Band Screw joint Buckles A(AX) | |||||||||||||||||||||||||||||
| XZYDFAE002 XZYDF00022 XZYDFAR001 | |||||||||||||||||||||||||||||
| Splicing by vulcanisation To avoid unnecessary downtime and difficult dismantling when carrying out preventive maintenance of process machinery, it is possible to split the V-Ring, fold it around the shaft and splice it. The V-Ring can be supplied either as a complete ring and cut on site, or supplied in the split condition from the factory. For V-Rings types RM and RME it is preferable to split the seals at the factory due to the size of the section. The best method of splicing a V-Ring is by vulcanising. Portable vulcanising tools for the different V-Rings profiles, vulcanising cement and detailed instructions are available from your local TSS company. | |||||||||||||||||||||||||||||
| Figure 58 FORSHEDA clamping band RM | |||||||||||||||||||||||||||||
| Latest information available atwww.tss.trelleborg.com Edition April 2007 | |||||||||||||||||||||||||||||
| TRELLEBORG sealing solutions | |||||||||||||||||||||||||||||
| 149 | |||||||||||||||||||||||||||||