| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | HPM-760s Installation | | |
| | | HPM-760s Installation | | |
| | | |
| | | |
| | | Figure below shows the Hastings piezo vacuum transducer. A standard 1/8" NPT male stem and evacuation port is provided for system connection. VCR and KF stem terminations are also available | | |
| | | Figure below shows the Hastings piezo vacuum transducer. A standard 1/8" NPT male stem and evacuation port is provided for system connection. VCR and KF stem terminations are also available When installing industrial transducers with threaded stem, apply an approved vacuum sealant to the stem threads of the transducer. Hand thread | | |
| | | |
| | | When installing transducers with threaded stem, apply an approved vacuum sealant to the stem threads of the transducer. Hand thread transducer into vacuum system, until joint is finger tight. Tighten transducer module completely using a wrench on the hexagonal portion of the stem. Do not grip instrument case to tighten; this will result in permanent damage to transducer ^ assembly. When the 760s is purchased indepen- L dently of the power supplyjdisplay, a connector supplier is provided so that the transducer can be connected as detailed in the figure. TRANSDUCER PIN-OUT PIN 1................SIGNAL OUTPUT (COM) PIN 2................SIGNAL OUTPUT (POS) PIN 3................15-30 VDC INPUT (COM) PIN 4................15-30 VDC INPUT (POS) Manual may be obtained at: http://www.teledyne-hi.com | | |
| | | |
| | | SPAN Adjustment ZERO Adjustment Electronics Module Stem Termination 1/8" NPT (shown) VCR and KF also available | | |
| | | SPAN Adjustment ZERO Adjustment Electronics Module Stem Termination 1/8" NPT (shown) VCR and KF also available | | |
| | | transducer into vacuum system, until joint is finger tight. Tighten transducer module completely using a wrench on the hexagonal portion of the stem. | | |
| | | |
| | | Do not grip instrument case to tighten; this will result in permanent damage to transducer assembly. When the 760s is purchased independently of the power supplyjdisplay, a connector is provided so that the transducer can be connected as detailed in the figure. TRANSDUCER PIN-OUT PIN I................SIGNAL OUTPUT (COM) PIN 2................SIGNAL OUTPUT (POS) PIN 3................15-30 VDC INPUT (COM) PIN 4................15-30 VDC INPUT (POS) Manual may be obtained at: http://www.teledyne-hi.com | | |
| | | N Connector Vin I | | |
| | | Pin 1 | | |
| | | |
| | | |
| | | |
| | | |
| | | Control # 166_122003B | | |
| | | Control # 166_122003B | | |
| | | |
| | | |
| | | |
| | | HPM-760s Installation | | |
| | | HPM-760s Installation | | |
| | | |
| | | |
| | | Figure below shows the Hastings piezo vacuum transducer. A standard 1/8" NPT male stem and evacuation port is provided for system connection. VCR and KF stem terminations are also available | | |
| | | Figure below shows the Hastings piezo vacuum transducer. A standard 1/8" NPT male stem and evacuation port is provided for system connection. VCR and KF stem terminations are also available When installing transducers with threaded stem, apply an approved vacuum sealant to the stem threads of the transducer. Hand thread | | |
| | | |
| | | When installing transducers with threaded stem, apply an approved vacuum sealant to the stem threads of the transducer. Hand thread transducer into vacuum system, until joint is finger tight. Tighten transducer module completely using a wrench on the hexagonal portion of the stem. Do not grip instrument case to tighten; this will result in permanent damage to transducer assembly. When the 760s is purchased independently of the power supplyjdisplay, a connector is provided so that the transducer can be connected as detailed in the figure. \Connector PIN 1................SIGNAL OUTPUT (COM) Pin 1 PIN 2................SIGNAL OUTPUT (POS) PIN 3................15-30 VDC INPUT (COM) PIN 4................15-30 VDC INPUT (POS) | | |
| | | |
| | | SPAN Adjustment ZERO Adjustment Electronics Module Stem Termination 1/8" NPT (shown) VCR and KF also available | | |
| | | SPAN Adjustment ZERO Adjustment Electronics Module Stem Termination 1/8" NPT (shown) VCR and KF also available | | |
| | | transducer into vacuum system, until joint is finger tight. Tighten transducer module completely using a wrench on the hexagonal portion of the stem. | | |
| | | |
| | | Do not grip instrument case to tighten; this will result in permanent damage to transducer assembly. When the 760s is purchased independently of the power supplyjdisplay, a connector is provided so that the transducer can be connected as detailed in the figure. TRANSDUCER PIN-OUT PIN 1................SIGNAL OUTPUT (COM) PIN 2................SIGNAL OUTPUT (POS) PIN 3................15-30 VDC INPUT (COM) PIN 4................15-30 VDC INPUT (POS) Manual may be obtained at: http://www.teledyne-hi.com | | |
| | | Pin 1 | | |
| | | |
| | | |
| | | |
| | | |
| | | | Control # 166_122003B | | |
| | | Control # 166_122003B | | |
| | | Manual may be obtained at: http://www.teledyne-hi.com | | |
| | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |