Columns & Plates
12Pages

{{requestButtons}}

Catalog excerpts

Columns & Plates - 1

COLUMNS & PLATES

Open the catalog to page 1
Columns & Plates - 2

COLUMNS & PLATES Fixture Plates • Extensive tapped dowel pin hole configuration provides the flexibility to accurately and quickly fixture practically any workpiece or mount any vise. • Fixture plates consist of alternating 1/2” dowel pin holes for workpiece location, along with 1/2” and 3/8” tapped holes for clamping. • Can be accurately located on machine tables by utilizing two reamed 5/8” centerline sine key holes. • Non-standard sizes and mounting configurations are available and will be quoted upon request – otherwise, mounting holes must me added by the customer. • TE-CO supports...

Open the catalog to page 2
Columns & Plates - 3

COLUMNS & PLATES Ball Lock™ Shanks and Liners • Shank & Bushing Material 4340 • Liner Material 52100 • Black Oxide Finish • Heat treatment: – Shanks: Rc 40-45 – Bushings: Rc 50-54 – Liners: Rc 62-64 Plate Shank Max. Max. Thickness Shank Dia. Holddown Screw + .005 Part (MM) Force Torque A No. B C D E (lbs) (lbs/ft) Ball Lock™ Receiver Bushings Back Mount Back Mount Back Mount Back Actual O.D. Depth C’bore Min. Face Shank Mount +.0000 +.000 +.006 Subplate Mount Dia. Part -.0004 -.002 Thickness Part (MM) No. A B C D No. Face Mount Face Mount Face Mount Actual Min. Clearance O.D. Subplate Drill...

Open the catalog to page 3
Columns & Plates - 4

COLUMNS & PLATES Columns • Provides an accurate fixturing base for workpieces on horizontal and multi-axis machining centers. • Provide a locating and mounting base for fixture plates. • Material: One-piece stress relieved class 40 Meehanite cast iron or equivalent. • Base and sides are milled flat, parallel, and square to .001 in 12”. • Columns are provided with the standard DIN and JIS mounting configuration (see page 206) and coolant drain holes. • Columns are plain, without a grid pattern or holes, on all four sides. • Grid patterns, non-standard mounting configurations, and special...

Open the catalog to page 4
Columns & Plates - 5

COLUMNS & PLATES T-Columns Approx. Weight Approx. Weight • Provides an accurate fixturing base for workpieces on horizontal and multi-axis machining centers. • Provide a locating and mounting base for fixture plates. • Material: One-piece stress relieved class 40 Meehanite cast iron or equivalent. • Base and upright thickness are milled flat, parallel, and square to .001 in 12”. • T-Columns are provided with the standard DIN and JIS mounting configuration (see page 209). • T-Columns are plain, without a grid pattern or holes, on all our sides. f • Grid patterns, non-standard mounting...

Open the catalog to page 5
Columns & Plates - 6

COLUMNS & PLATES Mounting Types for Tooling Blocks HOIST RING- SOCKET HEAD- MACHINE PALLET SOCKET HEAD SOCKET HEAD SOCKET HEAD EDGE LOCATOR MACHINE PALLET DIN Mounting incorporates a precision center hole for centering the Tooling Block and a precision offset radial hole for radial location on the pallet. To fasten the Tooling Block or plate once it has been located, simply tighten the Socket Head Cap Screws to the pallet. The Tooling Block or Plate is located onto a pallet by using two edges that have been precision ground that are perpendicular or 90 degree to each other. The Tooling...

Open the catalog to page 6
Columns & Plates - 7

COLUMNS & PLATES Tooling Plate Quotation Worksheet Special Request For Quotation: If you have a requirement that can not be met with one of our standards, please do the following: 1. Photocopy this page and the previous page – if it applies – for an accurate quote. 2. Fill in the information concerning the product that will be quoted. Sketch in any information that is not provided, being as detailed as possible. 3. Mail or fax the RFQ sheet to TE-CO. 4. Note: If ordered, this item will be manufactured directly from the information provided on this page. Please be sure information is...

Open the catalog to page 7
Columns & Plates - 8

COLUMNS & PLATES Column Quotation Worksheet Special Request For Quotation: If you have a requirement that can not be met with one of our standards, please do the following: 1. Photocopy this page and the previous page – if applicable – for an accurate quote. 2. Fill in the information concerning the product that will be quoted. Sketch in any information that is not provided, being as detailed as possible. 3. Mail or fax the RFQ sheet to TE-CO. 4. Note: If ordered, this item will be manufactured directly from the information provided on this page. Please be sure information is correct....

Open the catalog to page 8
Columns & Plates - 9

COLUMNS & PLATES Column Quotation Worksheet Special Request For Quotation: If you have a requirement that can not be met with one of our standards, please do the following: 1. Photocopy this page and the previous page – if applicable – for an accurate quote. 2. Fill in the information concerning the product that will be quoted. Sketch in any information that is not provided, being as detailed as possible. 3. Mail or fax the RFQ sheet to TE-CO. 4. Note: If ordered, this item will be manufactured directly from the information provided on this page. Please be sure information is correct....

Open the catalog to page 9
Columns & Plates - 10

COLUMNS & PLATES T-Column Quotation Worksheet Special Request For Quotation: If you have a requirement that can not be met with one of our standards, please do the following: 1. Photocopy this page and the previous page – if applicable – for an accurate quote. 2. Fill in the information concerning the product that will be quoted. Sketch in any information that is not provided, being as detailed as possible. 3. Mail or fax the RFQ sheet to TE-CO. 4. Note: If ordered, this item will be manufactured directly from the information provided on this page. Please be sure information is correct....

Open the catalog to page 10
Columns & Plates - 11

COLUMNS & PLATES T-Column Quotation Worksheet Special Request For Quotation: If you have a requirement that can not be met with one of our standards, please do the following: 1. Photocopy this page and the previous page – if applicable – for an accurate quote. 2. Fill in the information concerning the product that will be quoted. Sketch in any information that is not provided, being as detailed as possible. 3. Mail or fax the RFQ sheet to TE-CO. 4. Note: If ordered, this item will be manufactured directly from the information provided on this page. Please be sure information is correct....

Open the catalog to page 11

All TE-CO catalogs and technical brochures

  1. Plain Clamps

    1 Pages

  2. Hoist Rings

    22 Pages

  3. Toggle Clamps

    12 Pages

  4. Toolex Vises

    44 Pages

  5. 5-Axis Vise

    2 Pages

  6. Columns_Plates

    12 Pages

  7. Hoist ring

    22 Pages

  8. Toggle Clamp

    12 Pages