| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | Super heater | | |
| | | |
| | | Supply inlet attachment | | |
| | | SH41 | | |
| | | |
| | | 4| I | | |
| | | ^Please choose any from 3 kinds of left description. And, please enter in the end of the type. | | |
| | | |
| | | |
| | | Example : SH41 3200-3K- 40A | | |
| | | Standard | | |
| | | Flange Flange FD3 8 FD5 0 | | Socket 40A (Rp1 1/2 Female screw! | | |
| | | |
| | | |
| | | |
| | | |
| | | (<p3 8 Pipe! | | (<p5 0 Pipe) | | |
| | | |
| | | |
| | | heat | | |
| | | rial is1 | | |
| | | | |
| | | |
| | ina» | | |
| | | latin! | | |
| | | |
| | | | |
| | (Insu' | | |
| | | |
| | | Adiabatic cover DK4 1 Installation condition (OP) Performance curve- | | |
| | | MODEL : SH4 1 3200-4K-FD38 | | |
| | | |
| | | | | | | | | | | Model | SH41 | | | | Type | 3200-3K-I * | | 3200-4K-I * 1 | | | | Voltage 50/60Hz | 3-phase 2 00 V | | | | Heater capacity | 3kW | 4kW | | | | Max. hot-air temp. | 700 C | | | | Max. usable gas capacity | 2.5m3/mm | | | | Min. usable gas capacity | 0.20Nm3/mm | 0.27Nm3/mm | | | | Resisting pressure | Supply inlet attachment | | | | 40A : 490kPa ; FD38-50 : 30kPa | | | | Upper limit setting temp. of the overheat prevention sensor | B1:900°C B2: 650°C C:100°C Please set up less than the above temp. if you incorporate the temp. control | | | | Net weight | 4.7kg | | | | Open price | ¥202,000 | ¥202,000 | | | | Control No. | TIS 001 S 000 | TIS 001 S 000 | | | | | | | | | | |
| | | |
| | | Pressure loss curve (Heater OFF, No piping) | | |
| | | Hot-air curve | | |
| | | Temp. (°C
| | |
| | | Pressure loss(kPa! 8 | | |
| | | |
| | | |
| | | |
| | | 800 | | | | |
| | | | |
| | | 700 | | | 7 | | |
| | | | |
| | | 600 | | | 6 | | |
| | | | |
| | | 500 | | | 5 | | |
| | | | |
| | | 400 | | | 4 | | |
| | | | |
| | | 300 | | | 3 | | |
| | | | |
| | | 200 | | | 2 | | |
| | | | |
| | | 100 | | |
| | | |
| | | |
| | | 0 1 2 3 0 1 2 3 Gas capacity (Nm3/min) Gas capacity (m3/min; This is the performance on the side of the discharge at the inlet temp. 20 C. Gas capacity is measured with the air supply inlet. The red line is the hot-air temp. of the outlet in the time that the heater power supply manufacturers was input 100%. Temp. less than this curve is adjusted freely if temp. was controlled by TRC, FC, and CC siries. Please consult separately in the case that this is used in about min. gas capacity or about max.hot-air temp. | | |
| | | |
| | | •Different voltage specification (Order) : 3-phase 220V, 380V, 400V, 440V (50/60Hz) | | |
| | | |
| | | |
| | | Figure | | |
| | | |
| | | 28 | | 161 | | 86 | | 91.5 | | |
| | | |
| | | Air supply inlet (Selection method) FD38 :h=35 cp38 Pipe FD50 :h=36.5 cp50 Pipe 40A Socket : h=51 Rp1 1/2 (40A) | | |
| | | 140 | | |
| | | |
| | | Heater terminal (M5^ Temp. sensor connector terminal (M3)\ Ground terminal (M5) v Sensor wire inlet (Diameter of application cable <p10~<<p14 ) | | |
| | | |
| | | Power supply wire inlet | | |
| | | |
| | | (Diameter of application cable cp12~<p16 ) | | |
| | | |
| | | |
| | | 4-7X14 Long circle | | |
| | | |
| | | | | |
| | | |
| | | 5 | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |