• Products
  • Catalogues
  • Projects
  • News & Trends
  • Exhibitions

AMP AC Square Motors - 60 Pages

  1. P. 1

  2. P. 2

  3. P. 3

  4. P. 4

  5. P. 5

  6. P. 6

  7. P. 7

  8. P. 8

  9. P. 9

  10. P. 10

  11. P. 20

  12. P. 30

  13. P. 40

  14. P. 50

  15. P. 60

Catalogue excerpts

1 AMP Series 112 - 355 17-1000 kW 25-1400 HP 110-6400 Nm (at 1500min-1) AC Square Motors Catalogue-2010/01 E t-telectric.com

 Open the catalogue to page 1

Table of contents GENERAL INFORMATION . 4 BASIC DESIGN . 5 IEC standard 5 Insulation . 5 Temperature rise 5 Stator . 5 Winding 5 Thermal Protection . 5 Rotor 5 Vibration class and Balancing 5 Cooling and terminal box position 5 Mounting forms 5 Bearings . 5 Painting 5 DERATING AND TOLERANCES 6 Ambient temperature and altitude 6 Duty . 6 Overload capacity 6 Electrical and mechanical tolerances 6 NAME PLATE . 7 POWER SUPPLY CONNECTION . 7 OPTIONS 8 ENCODER . 9 IEC FLANGE DIMENSIONS . 10 PERMISSIBLE RADIAL LOADS 11 SELECT YOUR AMP 12 AMP IP 23 Selection curves 12 AMP IP 54/55 Selection curves . 13...

 Open the catalogue to page 3

4 General information T-T ELECTRIC proposes a series of square frame ac motors for variable speed drives applications. This asynchronous motor has been developed and designed to achieve the same dynamic performance as for DC motors series. The AC square motor complies with IEC600 34 standards and responds to the requirements for most industrial applications. Its flexible square frame design facilitates its integration into all types of machinery. AMP are 3 phase asynchronous squirrel cage 4 poles motors manufactured in degree of protection IP23 and IP54/55. 7 sizes (112-132-160-180-225-280-355)...

 Open the catalogue to page 4

5 Standards IEC600 34-1 Insulation Class H Temperature rise Class F Stator Fully square frame laminated, low loss, insulated on both faces. The laminations are welded together and the number of air channels through the iron core ensure a good heat transfer. Winding Conceived in order to withstand voltage peaks (du/dt) generated by the inverter. Thermal protection PTC 140°C thermistors (3 in series) in stator winding. PTC signal cable terminals are located into the terminal box. Rotor Consists of a core of laminations with the same magnetic properties as the stator laminations, and a squirrel cage...

 Open the catalogue to page 5

6 Derating and tolerances Ambient temperature and altitude Motors are designed to operate between -5°C to maximum 40°C ambient température and at a maximum altitude of 1000 m above sea level. If ambient temperature or altitude is higher then torque/power of the motor is derated according to the table below: Temperature (°C) Altitude (m) 30 40 50 60 1000 1 1 0.9 0.8 2000 1 0.93 0.85 0.75 3000 0.93 0.85 0.77 0.64 4000 0.85 0.73 0.65 0.5 Duty Motor power output can be increased depending on duty types defined by IEC600 34-1. Correction factors are given in the table below: Duty Operating time S2...

 Open the catalogue to page 6

7 The AMP motor and its fan blower AC motor have separate terminal boxes with 6 terminals inside. Connection can be star or delta according to nameplate information. Delta Connectio n Star Connectio n 1 W2 U2 V2 U1 V1 W1 W2 U2 V2 U1 V1 W1 Name plate Power supply connection 180-4B 147 703 2000 400V Y 263 0,85 0,95 67.4 162 4800 451 S1 23 06 1001 40 1000 H F 3 400 3,2 50 VFS 60 1024 5 TTL 6 0,012 Made in E.U. Terminal box Provided with plugged holes: 4 for main supply and 1 for accessories. Dimensions are according to table below : From frame size 225, 1 pre-bored face and 2 removable faces without...

 Open the catalogue to page 7

8 Options AMP112-355 S: standard x : possible R : on request Frame size AMP 112 132 160 180 225 280 355 Cooling forms IC06 (IP23) Force ventilated S S S S S S S IC17 (IP23) Single pipe ventilated x x x x x x x IC37 (IP54) Double pipe ventilated x x x x x x x IC416 (IP54) Totally enclosed, fan cooled S S S S S Other cooling forms available on request Mounting Forms IM1001 Horizontal foot (radial ventilation) S S S S S S S IM1001 Horizontal foot (axial ventilation) x x x x x x x IM1002 Horizontal foot, double shaft extension x x x x x x x IM2001 Horizontal foot and flange (radial ventilation) x...

 Open the catalogue to page 8

9 AMP motors are equipped with through hollow shaft encoder with insulating hollow shaft clamping. Encoders are programmable according to process requirements: Electrical interface: 5…32 V, TTL/ HTL Number of lines: up to 65536 IP23: motors delivered with M23 12-pin complete (male + female) connector . IP54: motors delivered with connection on the N-End shield via M23 12-pin complete (male + female) connector. An additional metal cover ensures protection of the encoder against mechanical damages. PIN Colour of wires Signal TTL, HTL 6 Brown A 5 White A 1 Black B 8 Pink B 4 Yellow Z 3 Lilac Z 10...

 Open the catalogue to page 9

11 The tables give the permissible radial loads in Newtons, assuming zero axial load. Radial load is applied at the middle of the shaft extension. The values are based on normal conditions at 50 Hz and 100 Hz for bearing life of 20000 hours for horizontally foot mounted motor (IM1001). Ball bearings Permissible radial loads Motor type Bearing type Distance from shaft shoulder (mm) At 1500 min-1 (N) At 3000 min-1 (N) AMP112-4 6308 2RSC3 40 2500 1800 AMP132-4 6310 2RSC3 55 3000 2200 AMP160-4 6214 2RSC3 55 3800 3000 AMP180-4 6216 2RSC3 70 4200 3200 AMP225-4 6220 C3 85 7500 5500 AMP280-4 6224 C3 105...

 Open the catalogue to page 11

12 Motor is dimensioned according to base speed, torque and constant power speed range. You can select your AMP using the following selection torque/speed curves 1- Calculate the nominal torque at the required nominal speed (T=9550 x P/n) 2- Select the frame size of your motor on the graphs below 3- Then you can select more exactly the required motor on the corresponding data sheet AMP IP 23 SELECTION CURVES You can select your AMP according to following torque/speed curves: Select your AMP 0 250 500 750 1000 1250 1500 1750 2000 500 1000 1500 2000 3000 AMP IP23 IC06 frames 112 to 225 (76 to 2000...

 Open the catalogue to page 12

13 AMP IP 54/55 selection curve Select your AMP 0 200 400 600 800 1000 1200 1400 500 1000 1500 2000 3000 torque (Nm) base speed (min-1) AMP IP54/55 IC416 frames 112 to 225 (50 to 1300 Nm) 112 132 160 225 180 Ext cst Power range f (Hz) U (V ) fN f1 f’1 fmax UN U’N Std cst Power range For IC666 (air to air exchanger) and IC86W (air to water exchanger) motors, please contact us. Supply voltage and extension of the constant power speed range As standard, motors are wound for 400V - constant power speed range from nN to n1 ( n1 approximately equal to 1.6 nN ). Extension of the constant power range...

 Open the catalogue to page 13

All T-T ELECTRIC catalogues and technical brochures

  1. DC Motors type DMP

    39 Pages

    En
  2. LAK DC MOTORS

    56 Pages

    En