Text version of the page

SMB135 Programmable Switch-mode, USB/AC Input Li+ Battery Charger with TurboChar g e™ Mode*

FEATURES & APPLICATIONS INTRODUCTION

Programmable USB/AC Li-Ion battery charger

The SMB135 is a programmable single-cell lithium-ion/lithium-polymer battery charger for a variety of portable applications. The device provides a simple and efficient way to charge high-capacity Li-Ion batteries via a USB port or an AC adapter. Unlike conventional devices, the SMB135’s high-efficiency operation eliminates large internal temperature rise and localized hot spot in handheld equipment. Summit’s proprietary TurboCharge

TurboCharge

TM

Mode: 750mA output from 500mA USB High-efficiency current-mode PWM controller

o 750kHz to 1.25MHz switching frequency o 0% to 100% duty-cycle

4.35 to 6.5V input voltage range

TM mode allows a 750mA charge current from a 500mA USB port, resulting to significantly reduced charge times. Charge control includes qualification, trickle-charge, pre-charge, constant current/constant voltage, and termination/safety settings that are fully programmable via a serial I2C/SMBus making the device truly a flexible solution. Fast charge current level (one or five unit loads) can be set via I

Small 1.3 x 2.1 uCSP

TM

-15 package (0.4mm pitch) High-accuracy output voltage regulation: 1% Low reverse leakage current Digital programming of all major parameters via I

2

C interface (with several addresses) and non-volatile memory

o Battery voltage set point
2 C or an input pin (USB500/100). An Enable (EN) pin is also provided for suspending USB charging and allowing the device to work in parallel with AC charger, which may already be integrated into a PMIC device. In this case, the SMB135 does not allow current to flow back to the USB port. The SMB135 offers a wide variety of features that protect the battery pack as well as the charger and input circuitry: over-current, under/over-voltage and thermal protection. Ultra-precise, 1% accurate, Kelvin-sensed ADOC™ technology allows accurate control of battery float voltage and improves battery capacity utilization. Status can be monitored via the serial port for charge state and fault conditions. In addition, one LED driver output can be used to signal charge status or an under-/over-voltage condition. As a protection mechanism, when the o Pre-charge, fast charge, termination current o Fast charge voltage threshold o Temperature limits o Automatic restart threshold

Status/Fault indicator Stability with ceramic capacitors Wide range of protection features

o Thermal monitor o Safety timers o Current limit junction temperature approaches approximately 110 C, the PWM switcher will start to cut back on the duty cycle, to reduce current. The SMB135 is available in a space-saving 1.3mm x 2.1mm uCSP o Input/output over-voltage lockout

Applications

GSM Handsets UMTS Handsets Portable Media & Gaming Players
TM Digital camcorders/still cameras package with lead-free balls as well as in a lead-free 5x5 QFN-32 package, and is rated over the -30 Handheld GPS/PDAs C to +85 C temperature range.

SIMPLIFIED APPLICATIONS DRAWING

SMB135

6.8uH IN GNDSTAT 4.7uF 10uF 500-700mA4.35V-6.5V VDDCAP 1uF SENSEHSENSEL 50-100m BATTCOMP R D+D-VDCGND SCL LIM USBController Li-Ion THERM LED EN OUT USB500/100SDA ADC+ADC- C comp R comp

Figure 1 – Applications block diagram featuring the SMB135 programmable switch-mode battery charger. * Patent Pending

© SUMMIT Microelectronics, Inc. 2006
• 757 North Mary Avenue • Sunnyvale CA 94085 • Phone 408 523-1000 • FAX 408 523-1266

http://www.summitmicro.com/

2106 3.1 11/4/2008

1