Stonclad GS - Stonhard - #2

Each unit of Stonclad GS will cover approximately 200 sq. ft./18.58 sq. m of surface at a nominal 1/4 in./6 mm thickness.

• When the blender stops, scrape off excess from the mixing blade and remove the pail, delivering it to the floor area for application.

After mixing, Stonclad GS has a working time of approximately 25 minutes at 70°F/21°C. The working time will vary depending upon temperature.

• Material must be used immediately after mixing.

• A Screed Applicator is used to distribute the mixed Stonclad GS onto the floor.

• Steel finishing trowels are used to compact and smooth the surface of the material to the required thickness.

• Detailed instructions on application and installation can be found in Stonhard's Stonclad GS Directions.

• DO NOT attempt to install material if the temperature of Stonclad GS components and substrate are not within 60 to 85°F/16 to 30°C. The cure time and application properties of the material are severely affected at temperatures outside of this range.

• DO NOT use water or steam in the vicinity of the application. Moisture can seriously affect the working time and other properties.

• The use of NIOSH/MSHA approved respirators and safety glasses is recommended.

• Avoid contact with all liquid Parts A and B as they may cause skin and/or eye irritation. Workmen

Store all components of Stonclad GS between 60 to 85°F/16 to 30°C in a dry area. Avoid excessive heat and do not freeze. The shelf life is 3 years in the original, unopened container.

Stonclad GS is available in 12 standard colors. Refer to the Stonclad Color Sheet.

Proper preparation is critical to ensure an adequate bond. The substrate must be dry and free of all wax, grease, oils, fats, soil, loose or foreign materials and laitance. Laitance and unbonded cement particles must be removed by mechanical methods, i.e., abrasive blasting or scarifying. Other contaminants may be removed by scrubbing with a heavy-duty industrial detergent (Stonkleen DG9) and rinsing with clean water. The surface must show open pores throughout and have a sandpaper texture. For recommendations or additional information regarding substrate preparation, contact Stonhard's Technical Service Department.

The use of Standard Primer is necessary for all applications of Stonclad GS over all substrates except Stonset grouts. Over Stonset grouts, Stonhard's Stonset Primer is used. The Standard or Stonset Primer must be tacky during the application of Stonclad GS. If the primer becomes tack-free, the area must be re-primed prior to continuing the application.

should cover hands with

ruuuer yiu\

ventilation.

es.

Use only with adequate

Procedures for maintenance of the flooring system during operations are described in the Stonclad Cleaning Procedures.

Specific information regarding chemical resistance is available in the Stonclad Chemical Resistance Guide.

Material Safety Data Sheets for Stonclad GS are available upon request.

A staff of technical service engineers is available to assist with installation or to answer questions related to Stonhard flooring products. Requests for technical service or literature can be made through local sales representatives and offices, or corporate offices located worldwide.

Empty the entire contents of one foil bag of Part A (liquid) and one poly bag of Part B (liquid) into a mixing pail.

Place the mixing pail on a JB Power Blender and activate the timer to start the one minute blending cycle.

When the blender stops, reactivate the timer and immediately pour the entire contents of one bag of Part C (aggregate) into the rotating pail. Allow the contents to mix for the complete one minute cycle.

IMPORTANT:

Stonhard believes the Information contained here to be true and accurate as of the date of publication. Stonhard makes no warranty, expressed or implied, based on this literature and assumes no responsibility for consequential or incidental damages in the use of the systems described, including any warranty of merchantability or fitness. Information contained here is for evaluation only. We further reserve the right to modify and change products or literature at any time and without prior notice. 3/08

Rev. 3/08

www.stonhard.com

A Division of

nc.

USA 800.257.7953 Canada (905)430.3333

(32)2.720.8982

(971)4.3470460

(52)55.9140.4500 (54-3327)44.2222

Europe Middle East

Mexico

South America

Africa (27)11.254.5500

Asia (86)21.5466.5118