Text version of the page 
Text version of the page 
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Technical data Designation SKF rri2o performance Voltage, V/Hz Work piece: - Maximum weight - Maximum bore diameter - Range - Magnetic probe -Accuracy (electronics) Time control: - Range - Accuracy Demagnetisation according to SKF norms (automatic) Can heat sealed bearings Can heat pre - greased bearings Error guiding codes Thermal overload protection Maximum magnetic flux Control panel Operating area (w « h) Coil diameter Dimensions (w«d«h) Total weight, including yokes Maximum power consumption | | | | | | TIH 100m 97 kg (213 lb) 230V/50-60Hz or 400-460V/50-60Hz 120 kg (264 lb) 20-400 mm (0,8-15,7 in) 0-250°C(32 -482 °F) Yes, K-type ±2°C(± 3,6 °F) 0-60 minutes ± 0,01 sec. 400 °C(750 °F) Yes Yes 2-step;50-100% Yes (<2 A/cm) Yes Yes Yes Yes 1,7 T KeyboardwithLED inremotecontrol 155 * 205 mm (6,1 * 8,0 in) 110 mm (4,3 in) 570 * 230 * 350 mm (22,4 * 9,0 * 13,7 in) 42 kg (92 lb) 3,6 kVA (230V) | | | | | | | | | | 4,0-4,6 kVA (400-460V) Number of standard yokes 3 | | | | | | | | | | 56 * 56 * 296 mm (2,2 * 2,2 * 11,7 in), for heating bearings with bore diameter of 80 mm (3,1 in) and larger 28 * 28 * 296 mm (1,1 * 1,1 * 11,7 in),for heating bearings with bore diameter of 40 mm (1,6 in) and larger 14 * 14 * 296 mm (0,6 * 0,6 * 11,7 in), for heating bearings with bore diameter of 20 mm (0,8 in) and larger 56 * 56 mm (2,2 * 2,2 in) Yes, foldable No Yes, large yoke only No Steel and glass filled polyamide 3 years | | | | | | Standard yokes | | | | | | | | | | Core cross section Yoke storage Sliding arm Swivel arm Cooling fan Housing material Warranty period | | | | | | | | | | d (mm] | | | | | | Selection guide There are no totally restrictive guidelines to follow when choosing your SKF bearing heater. It will depend upon the type and geometrical dimensions ofthe components you want to heat. Nevertheless, SKF offers the following helpful general selection guide. SKF m2o concept ■m2o" represents the weight (kg) ofthe heaviest SRB 231 bearing which can be heated from 20 to 110 °C (68 to 230 °F) in 20 minutes. This defines the heater's power output instead of its power consumption. | | | | | | | | | | 801 | | | | | | | | | | 60C | | | | | | | | | | kg | | | | | | | | | | 30 4C | | 100 120 210 300 44C | | 70C | | | | | | | | | | = TMBH 1 = TIH 030m | | = TIH100m = TIH210m | | E | | = TIH 240 = m2c | | | | | | | | | | | | | | | | | | | | | | / SKF Maintenance Products ® SKF is a registered trademark of the SKF Group | | | | | | | | | WWW maprOSkf COm The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless permission is granted Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss WWW.Skf.COm/mOUnt or damage whether direct, indirect or consequential arising out of use of the information contained herein. | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
|