| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
| | | |
| | | © Siemens AG 2007 | | |
| | | |
| | | Electropneumatic positioners SIPART PS2 | | |
| | | |
| | | Technical specifications all versions | | |
| | | |
| | | • Noise (digitally controlled) to DIN EN 60068-2-64/08.95 | | 10 ... 200 Hz; 1 (m/s2)2/Hz (3.28 (ft/s2)2/Hz) 200 ... 500 Hz; 0.3 (m/s2)2/Hz (0.98 (ft/s2)2/Hz) 4 hours/axis < 30 m/s2 (< 98.4 ft/s2) without resonance sharpness | | |
| | | ■ Technical specifications | | |
| | | |
| | | |
| | | SIPART PS2 (all versions) | | |
| | | |
| | | General data Angle of rotation (part-turn actuators) Installation • On linear actuators | | |
| | | 3 ... 130 mm (0.12 ... 5.12 inch) (angle of feedback shaft 16 ... 90°) 30 ... 100° | | |
| | | • Recommended continuous duty range of the complete fitting Weight, basic device • Plastic casing • Metal casing, aluminium • Metal casing, stainless steel • Metal casing EEx d version Dimensions | | |
| | | |
| | | |
| | | Approx. 0.9 kg (1.98 lb) Approx. 1.3 kg (2.86 lb) Approx. 3.9 kg (8.58 lb) Approx. 5.2 kg (11.46 lb) See Dimensional drawings To DIN EN 60721-3-4 1K5, but -40 ... +80 °C (1K5, but -40 ... +176 °F) 2K4, but -40 ... +80 °C (2K4, but -40 ... +176 °F) 4K3, but -30 ... +80 °C3) (4K3, but -22 ... +176 °F) | | |
| | | Using attachment set 6DR4004-8V and where necessary with an additional lever arm 6DR4004-8L on actuators according to IEC 534-6 (NAMUR) with ribs, bars or flat face Using attachment set 6DR4004-8D on actuators with mounting plane according to VDI/VDE 3845 and DIN 3337: The required mounting console has to be provided on the actuator side; shaft with groove and female thread M6 | | |
| | | |
| | | |
| | | Climate class 4 • Storage1) •Transport^ • Operation2) | | |
| | | ■ On part-turn actuators | | |
| | | |
| | | |
| | | |
| | | Certificate and approvals Classification according to pressure equipment directive (DRGL 97/23/EC) | | |
| | | |
| | | Controller • Five-point switch • Dead zone - dEbA = Auto - dEbA = 0.1 ... 10% • Scan time • Resolution • Transmission error • Temperature effect Cycle time • 20 mA/HART device • PA device • FF device Binary input BE1 (terminals 9/10; electrically connected to the basic device) Degree of protection CE marking | | |
| | | For gases of fluid group 1, complies with requirements of article 3, paragraph 3 (sound engineering practice SEP) | | |
| | | Self-adjusting | | |
| | | |
| | | |
| | | |
| | | Self-adjusting or can be set as fixed value Self-adjusting or can be set as fixed value | | |
| | | Pneumatic data Power supply • Pressure Air quality to ISO 8573-1 • Solid particle size and density • Pressure dew point • Oil content Unthrottled flow • Inlet air valve (ventilate actuator)4) - 2 bar (29 psi) - 4 bar (58 psi) - 6 bar (87 psi) • Outlet air valve (ventilate actuator)4) - 2 bar (29 psi) - 4 bar (58 psi) - 6 bar (87 psi) Valve leakage Throttle ratio Power consumption in the controlled state Types of actuators • In plastic casing • In aluminium casing • In flameproof casing • In stainless steel casing | | |
| | | Compressed air, nitrogen or cleaned natural gas 1.4 ... 7 bar (20.3 ... 101.5 psi): Sufficiently greater than max. drive pressure (actuating pressure) | | |
| | | |
| | | 10 ms < 0.05% < 0.2% < 0.1%/10 K (< 0.1%/18 °F) 20 ms 60 ms 60 ms (min. loop time) Suitable only for floating contact; max. contact load < 5 mA with 3 V IP66 to EN 60 529/NEMA 4x Conformity as regards EMC Directive 89/336 EC in accordance with the following standards EN 61326/A1 Appendix A.1 and NAMUR NE21 August 98 | | |
| | | |
| | | Class 2 Class 2 (min. 20 K (36 °F) below ambient temperature) Class 2 | | |
| | | |
| | | 4.1 Nm3/h (18.1 USgpm) 7.1 Nm3/h (31.3 USgpm) 9.8 Nm3/h (43.1 USgpm) | | |
| | | |
| | | |
| | | 8.2 Nm3/h (36.1 USgpm) 13.7 Nm3/h (60.3 USgpm) 19.2 Nm3/h (84.5 USgpm) < 6-10-4 Nm3/h (0.0026 USgpm) Adjustable up to ~ : 1 < 3.6-10-2 Nm3/h (0.158 USgpm) | | |
| | | EMC requirements Material • Housing - 6DR5..0-... (plastic) - 6DR5..1-... (metal) - 6DR5..2-... (stainless steel) - 6DR5..5-... (metal, pressure-proof) • Harmonic oscillations (sine-wave) according to DIN EN 60062-2-6/05.96 | | |
| | | |
| | | |
| | | Glass-fiber-reinforced Macrolon GD AISi12 Austenitic stainless steel mat. No. 1.4581 GK AISi12 Aluminium AIMgSi, anodized | | |
| | | Single-action and double-action Single-action Single-action and double-action Single-action and double-action | | |
| | | |
| | | 1: | | |
| | | During commissioning at < 0 °C (< 32 °F) make sure that the valves are flushed long enough with the dry medium. At < -10 °C (14 °F) the display refresh rate of the LCD is limited. Only T4 is permissible when using Iy module. -25 ... +75 °C (-13 ... +167 °F) for 6DR55..-0G..., 6DR56..-0G..., 6DR55..-0D... and 6DR56..-0D... With EEx d version (6DR5..5-...) the values are reduced by approx. 20% | | |
| | | |
| | | |
| | | 2) | | |
| | | |
| | | 3.5 mm (0.14 inch), 2 ... 27 Hz 3 cycles/axis 98.1 m/s2 (321.84 ft/s2), 27 ... 300 Hz, 3 cycles/axis 150 m/s2 (492 ft/s2), 6 ms, 1000 shocks/axis | | |
| | | 3) | | |
| | | |
| | | 4) | | |
| | | |
| | | |
| | | |
| | | ■ Bumping (half-sine) to DIN EN 60068-2-29/03.95 | | |
| | | |
| | | Siemens FI 01 • 2008 | | |
| | | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |