I/O DIGITAL MODULES

6 opto-isolated inputs contacts 2 relay 5 A, 250 Vac outputs

I OUT I OUT

“Stand-alone” operating mode: -D- IO connected to industrial motor controller device or valves “Distributed” operating mode, control logic from supervisory system

IO

10 short circuit protected Mosfet output channels. Each output rated at 500mA from 6 to 35 Vdc 10 opto-isolated inputs suitable for reed relays, Outputs protected against short circuit and overvoltage conditions igital Inuts module // RS igital Oututs module // RS igital Inuts module // RS igital Oututs module // RS igital Inuts / igital Outus control module Programmablecomms failure state for outputs proximity switches, npn & pnp and Diagnostic EDs show output state, open circuit, overload O
RR C
O -D-IN -D-OUT -10-D-IN -10-D-OUT -D-I-O 5 SPST N/O relay output module SIAS contact closure I
PUTS /O 5 opto-isolated inputs suitable for reed relays, 5A 250Vac resistive loads 8 inputs to 100H with 16 bit totalisers
UTPUTS /
ATURS proximity switches, npn & pnp and 2A 250Vac inductive loads 2 inputs to 10H with 32 bit totalisers contact closure Counts up to 100H Maximum total current 12A per module the rated capacity of the singe common terminal Operates in count, frequency, period and on or off time modes to 100H 1 fast count channel to 10H Programmablecomms failure state for relays Operates in count or frequency mode to 10H 16 bit totaliser for each channel Programmable delay, 50ms to 2.5 sec Inputs protected from transients up to 600W/ms 5 250 ms anti -bounce filter “I/O” operating mode, ModBUS I/O functions COMMUICATIO I
TRAC 2 wire S85 2 wire S85 2 wire S85 2 wire S85 2 wire S85 P
ROTOCO ModBUS TU Slave ModBUS TU Slave ModBUS TU Slave ModBUS TU Slave ModBUS TU Slave S
P 800 to 5600 bps 800 to 5600 bps 800 to 5600 bps 800 to 5600 bps 800 to 5600 bps C
OMMSISTACMA 1,200 m 1,200 m 1,200 m 1,200 m 1,200 m Parameter setting Motor / Valves control and alarms tasks Filter time, fail state, Baud rate and address S
AMPI TIM 300 ms 300 ms 200 / 00 ms 20 / 50 ms Parameter setting Parameter setting C
OMMUICATIO TIM 20 ms 38,00 Baud 20 ms 38,00 Baud 20 ms 38,00 Baud 20 ms 38,00 Baud Delay, fail state, Baud rate and address) Filter time, input type, Baud rate and address S
OTAR Parameter setting P
RORAMMI Filter time, input type, Baud rate and address RA ATA P
OR SUPP 190 Vdc (9 30 opt.) 190 Vdc (9 30 opt.) 190 Vdc (9 30 opt.) 190 Vdc (9 30 opt.) 10..0 Vdc 19..28Vac, 50..60 H 1928 Vac, 50-60 H 1928 Vac, 50-60 H 1928 Vac, 50-60 H 1928 Vac, 50-60 H P
OR COSUMPTIO 2.5 W 2.5 W 2.5 W 1.5 W 2 W
AAIC I
SOATIO 1,500 Vac 1,500 Vac 1,500 Vac 1,500 Vac Input // Supply (1.5 kV) Input // Outputs (3.5 kV)
ROT P
A Power On Power On Power On Power On Poer On I
ICATIO S Failure / Error Failure / Error Failure / Error Failure / Error Fail Transmit Data (Tx) Transmit Data (Tx) Transmit Data (Tx) Transmit Data (Tx) Transmit Data (Tx) eceive Data (x) eceive Data (x) eceive Data (x) eceive Data (x) eceive Data (x) 5 Input Status 5 Output Status 10 Input Status 10 Output Status 6 input status 2 output status O
PRATI TMP 0 to55 C 0 to55 C 0 to 55 C 0 to 55 C 0 to 60 C S
TORA -20 to 0 C -20 to0 C -20 to 0 C -20 to 0 C -20 to 0 C M
A UMIIT 30..90 0 C non condensing 30..90 0 C non condensing 30..90 0 C non condensing 30..90 0 C non condensing 30..90 0 C non condensing P
ROTCTIO IP20 IP20 IP20 IP20 IP20 C
OCTIOS Screw clamp, plug in connectors, 2.5mm
2 max Screw clamp, plug in connectors, 2.5mm
2 max Screw clamp, plug in connectors, 2.5mm
2 max Screw clamp, plug in connectors, 2.5mm
2 max Screw clamp, plug in connectors, 2.5mm
2 max M
OUTI 35mm symmetrical DIN rail 35mm symmetrical DIN rail 35mm symmetrical DIN rail 35mm symmetrical DIN rail 35mm symmetrical DIN rail
IMSIOS 1.5 x 100 x 112 mm 1.5 x 100 x 112 mm 1.5 x 100 x 112 mm 1.5 x 100 x 112 mm 1.5 x 100 x 112 mm
OT SAPPI yes yes yes yes yes
IT 200 g 200 g 200 g 200 g 200 g S
TAARS EN 50081-2, EN 55011, EN 50082-2, EN 61000-2-2/, EN 5010/11, EN 61010-1 EN 50081-2, EN 55011, EN 50082-2, EN 61000-2-2/, EN 5010/11, EN 61010-1 EN 50081-2, EN 55011, EN 50082-2, EN 61000-2-2/, EN 5010/11, EN 61010-1 EN 50081-2, EN 55011, EN 50082-2, EN 61000-2-2/, EN 5010/11, EN 61010-1 EN 61000-6-/2002 (Emissioni), EN 61000-6- 2/2002 (Immunit), EN 61010, IEC1131