Catalogue New Position switches according to DIN EN 50047 and DIN EN 50041
www.schmersal.com
print switch display
Page / 48
Make a request   
SCHMERSAL - 138645
/ 48
See other catalogues for SCHMERSAL
Text version of the page
Slow action (T) Snap action with end-position latching (R) With slow action, there is a differential travel between the opening of the NC contact and the closing of the NO contact; the contacts are not switched simultaneously. The switching points are in exactly the same position during actuation and return switching of the position switching. The switching movement depends on the actuating speed. Slow action is possible with overlapping or with staggered contacts. In case of overlapping contacts, the NO and the NC contacts are si- multaneously closed for a short moment during the switching process. Staggered contacts are possible for two contacts of the same type (i.e. two NC or two NO contacts); the contacts are switched one after the other. An end-position latching function is not pos- sible. Position switches with end-position latching have no return spring and therefore must be put back into the initial position manually after each operation. The end-position latching is only available with snap action position switches.

Position switches according to DIN EN 50047 and DIN EN 50041 Contact variants and switching behaviour Contact variants

Snap action Z Slow action T

Switching behaviour

1 NO contact 1 NC contacts -110 NO contact 2 NC contacts -02 2 NO contact 0 NC contacts -20 Slow action with overlapping contacts T, W1 T, W3 Snap action (Z) Slow action with staggered contacts Latching function R With snap action there is no differential travel between the opening of the NC contact and the closing of the NO contact, i.e. the NC and NO contacts are switched simultaneously. The switching movement occurs snap wise and independent from the actuating speed. Becau- se of the switching hysteresis, the switching points are different when actuating or releasing the switch. This switching system is used when the NC and NO contact must operate simultaneously and no intermediate positions (i.e. either one or the other circuit must be closed) are desired. A latching function is possible. Switching point after ...mmPositive break travel Switching contacts
Pre-travelAfter-travel
13-1421-2221-22

63,52,5

13-14

3,3

21-22 13-14

162,54,3

63,53,5 13-14 23-24 Contact variantsSnap actionSlow action with latching functionwith overlap-ping contactswith stagge-red contacts SÖZRTT..W1T..W3 11 zzzz 20 z 02 zzzz

9

DirectIndustry's Virtual Technical Library: PDF Catalogue | Technical Documentation | Brochure | Manual | Industrial directory | Specifications | Characteristics
Search Go
page 1 p.1
page 2 p.2
page 3 p.3
page 4 p.4
page 5 p.5
page 6 p.6
page 7 p.7
page 8 p.8
page 9 p.9
page 10 p.10
page 11 p.11
page 12 p.12
page 13 p.13
page 14 p.14
page 15 p.15
page 16 p.16
page 17 p.17
page 18 p.18
page 19 p.19
page 20 p.20
page 21 p.21
page 22 p.22
page 23 p.23
page 24 p.24
page 25 p.25
page 26 p.26
page 27 p.27
page 28 p.28
page 29 p.29
page 30 p.30
page 31 p.31
page 32 p.32
page 33 p.33
page 34 p.34
page 35 p.35
page 36 p.36
page 37 p.37
page 38 p.38
page 39 p.39
page 40 p.40
page 41 p.41
page 42 p.42
page 43 p.43
page 44 p.44
page 45 p.45
page 46 p.46
page 47 p.47
page 48 p.48
pdf-page pdf di En 2008-10-42-13