AS-Interface Safety at Work - SCHMERSAL - #28

Text version of the page

28 R C S OR AS-Interface Safety at Work AZM 170 AS Technical data ø 4,2 22 15 90 31 60 23 8 30 30 8 M12 37 • Solenoid interlock in 2 versions: AZM 170 B ST-AS: Release, when door is closed AZM 170 BZ ST-AS: AS-i split code 1, when door is closed AS-i split code 2, when door is locked • High holding force 1,000 N • Integrated AS-Interface • AS-Interface LED and status display • AS-Interface M12 connector • AS-Interface magnet control • Solenoid power supply via 24 VDC • Manual release for power to unlock • Protection class IP 67 Ordering details Technical data Note Manual release from side • For manual release using M5 triangular key, available as accessory • Only available for power to unlock principle • Ordering suffix -2197 AZM 170 À ST-AS ÁÂPà Nr. Option Beschreibung À B Actuator monitored BZ Combined monitoring of actuator/solenoid interlock Á Latching force 5 N R Latching force 30 N  Power to unlock A Power to lock à 2197 Manual release for power to unlock Ambient conditions: Ambient temperature: – 25 °C … + 55 ºC Storage and transport temperature: – 25 °C … + 85 °C Relative humidity: 30% … 95%, non-condensing, non-icing Resistance to vibration: 10 ... 150 Hz, amplitude 0.35 mm Resistance to shock: 30 g / 11 ms Switching frequency f: £ 1 Hz Switch-off delay: < 100 ms Actuating speed: £ 2 m/s Classification: *approvals under preparation If a fault exclusion for hazardous damage of the 1-channel mechanics is authorized and an adequate protection against tampering is ensured, suitable for use up to: Standards: EN ISO 13849-1; IEC 61508 PL: up to d Category: up to 3 PFH value: 1,01 x 10-7 /h for max. 100.000 operations/year SIL: up to 2 Service life: 20 years Basically suitable up to: Standards: EN ISO 13849-1; IEC 61508 PL: up to c Category: up to 1 PFH value: 1,16 x 10-6 /h for max. 100.000 operations/year SIL: up to 1 Service life: 20 years Note The solenoid interlock and the actuator unit must be ordered separately! Interlocks with power to lock principle may only be used after a thorough evaluation of the accident risk, since the safety guard can be opened immediately on failure of the power supply or upon activation of the main switch. The addressing must take place via the M12 connector. 1: AS-i + 2: Aux – (P) 3: AS-i – 4: Aux + (P) 1 4 2 3 C Approvals F* * * under preparation Standards: EN 50295, EN 60947-5-1, EN ISO 13849-1, IEC 61508 Enclosure: glass-fibre reinforced thermoplastic, self-extinguishing Actuator and locking bolt: stainless steel Mechanical life: ³ 1 million operations Fmax: 1000 N Holding force: typically 30 N for suffix R Protection class: IP 67 to IEC/EN 60529 Protection class: II, X Overvoltage category: III Degree of pollution: 3 Connection: Connector M12, 4 poles Electrical data AS-Interface: Operating voltage: 26.5 ... 31.6 VDC, via AS-Interface, reverse-polarity proof Operating current: max. 0,1 A AS-Interface specification: (V 2.1) Profile S-7.B IO-Code 0x7 ID-Code 0xB ID-Code1: 0xF ID-Code2 0xE AS-I inputs: Data bits D0 ... D3: static code 0 or dynamic code transmission AS-I outputs: Bit 0 Solenoid control Bit 1 ... Bit 3 not used Parameter port: P0: Actuator present P1: Interlock locked P2: no function P3: no function Input module address: preset to address 0, can be modified by means of the AS-Interface bus master or the hand programming device Diagnostic display: LED grün AS-i supply voltage on LED rot AS-i communication error or slave address = 0 LED gelb Enabling status Auxiliary voltage (Aux): Operating voltage: 24 VDC (– 15% / + 10%) (stabilised PELV) Operating current: max. 0,5 A Magnet: 100% ED Device fuse: £ 4 A when used to UL 508